Hi . . Look for all folders with SCREEN and CG . . Also Preferences . . Using search . . .
Type: Posts; User: TC542; Keyword(s):
Hi . . Look for all folders with SCREEN and CG . . Also Preferences . . Using search . . .
Hi . . When you reinstall the CGenius s/w . . Always remove any previous drivers, etc. relating to CG and SCREEN . . flush out any 'Preferences' otherwise the s/w will load and use the old/corrupted...
Cheers fri3nd . . .
Good to meet an enthusiastic Cezanne engineer . . . ;-)
Regards, Tony
An Adaptec 2930U will also be OK . . . ;-)
I'll check my stock . . .
Tony
Hi . . The SCSI is standard, with the SCSI ID set at '6' for the scanner (at the rear of the scanner . .). . .
Therefore you will be able to connect another device as long as the terminator is...
Hi Tony-Wu . . .
Oh Oh! . . If you removed the lens to clean it, you will need a special jig and special 'Glass Jig' to set it up correctly . . !!!
(Even I do not have one of these jigs . . and I...
'SCONT' board is the main control board at the rear of the 'FT-S5500' scanner.
(For the FT-S5000 it is the 'JCONT' board . . .a totally different one . . .)
BR, Tony
I am looking to sell the lot as a package . . .
There is so much, I think people will be shocked to see it . . .
Mostly stored in their original SCREEN boxes.
Also, I have various Firmwares...
Hi Peter . . . Yes . . .Middle of England . . Near to the famous British Grand Prix circuit . . .:-)
Hi All . . .
Am moving house soon and need space . . .Does anyone know of someone who wants a fully working 'Cezanne Elite'/FT-S5500 . . ??
I have many many many accessories . . .(Having been a...
Hi Fabio . . . .
Once you have been able to get a new set of bearing . . . called 'Resin Bearings' . . .
You will need to follow the attached procedure . . . .
'Resin Bearing adjustment'
Follow...
FT-S5000 has 4 lamps . . FT-S5500/Elite has 3 lamps . . . Upper 1 for transmission . . Lower 2 for reflection.
You must have a Transmission lamp in place during initialisation . . !!
The system...
Hi Bruce . . .
Don't know the voltage at the lamp mounts due to the 'Inverter' voltage needed for the standard lamps.
But the voltage at the supply connector to the inverter, Yellow and Black...
Hi . . .
Here is a picture attached of the 3 feet that my FT-S5500 scanner sits on . . .
Regards, TC542
Hi All . . .
Just like to say that some information is correct . . But some is incorrect.
Definitely need a sturdy table to stand the scanner on . . (One that folds away is useless . . .!!)
The...
Hi Ned . . . . I am sure that there is nopont is trying to extract the 'hqx' files . . These are a special SCREEN protected file.
What you need is a full copy of CG EX. . . You do not need to know...
Hi Tony . . .
It is good that you have MacOS 9.2 using CSPro3 1.2.x . . . But other things need to match for it to work properly.
(It was a nightmare to support softwares during my time with...
Hi Felix . . .
Once powered 'On' . . Does the machine go through a full cycle . . and finish with the 3 LEDs at the front cycling . . ?
If so, then the machine has gone through a full cycling of...
Correct . . The Glass Tray . . for Line-Art scanning . .is a clear glass.
I will try and get a quote for shipping of both the Standard and Glass trays . . inc. insurance . . .
Watch this space . ....
Hi Floyd . . .
Which glass tray would you be interested in . . .Standard or Clear . . ?
I'd be a bit worried about shipping the tray to NY . . . People handling it . . . Even in the proper...
Hi Floyd . . . I may have a secondhand glass available . . . Been used, but not extensively . . (Used on training courses only . . . )
Whereabouts are you? . . Can ship in an original box.
Also,...
@TC542: Thanks for the hint. Do you have an abstract of the mentioned procedure? Would it be possible to simulate the Glass Jig with any kind of calibration slide (USAF chart)? Did the procedure...
Hi All . . . .
After replacing any parts on the machine . . e.g. Lens, CCD, linear guides, rails, etc. you will need a jig to align all the resolutions . . (11 off . . )
The jig is called a 'Glass...
Hi Stefano . . .
If the machine is completely dead, i.e. no LED's at all, then probably it is a power supply failure.
It is situated at the left hand side . . . Remove the tray protection to get...
Hi . . . Please read the attached files before you try and swap over from one MacOS to another . . . !!
Hopefully you are currently using an Adaptec 29160N SCSI card that you are using . . .?
Info...
Hi . . .
You cannot remove the 2 Transparency lamps . . . !! These are used during 'Initialisation' the do an 'Overview' scan.
Hence you will get an error. . . . !!
(You can remove the Reflection...
Hi . . . . The scanner does sit on 3 Feet only . . . There should be 'anti-vibration rubber spacers under the feet aswell.
(If you don't have these you can use layers of rubber mouse mats . . . ;-)...
Hi . . .
Before you try to move the scanner you must put it into transport mode . . . !! . . The optics can easily get damaged/misaligned if you do not.
Firstly, the transport bracket is normally...
Okay by me to download these files . . . Seems like these sites are the only places to get decent info about the scanners . . . ;-)
Regards, Tony
Hi All . . . I have been asked to resend files relating to the MacOS and SCSI cards for the FT-S5000 and FT-S5500 . . .
(Please read these carefully . . . It is not logical sometimes . . . (e.g.CG...
Hi . . . I'm sure I have copies of the older, 'ColorScopePro' manuals . . . However, it would be much better for you to upgrade to 'ColorGenius' on your FT-S5000. However, You do have to ensure you...
Hi . . .
Following on from my previous post . . .
I have prepared a PDF document highlighting the 'Accessories' for the Cezanne scanner that I have . . .
(May also help with the 'Oil Tray' issue...
Hi . . . I believe this is the clear glass tray that is used for 'Line-Art' scanning. (I will need to double check with my collection. . . .)
I will post pictures of the 'Standard'/'frosted'/...
Sorry for the late reply to your previous connection issue . . .I sent it by direct reply, which went to the site administrator . . .Ooopps!! . .
This is what I sent . . .
"Hi . . .
Before doing...
. . . following on . . .There are only 11 actual resolutions that do not get interpolated . . . !!
But this is not relative to your problem, as you have been working fine before . . . ;-)
BR, Tony
Hi Patrick . . Sorry for the late reply . . . It is interesting that you say that the image is clearer towards the middle of the tray . . i.e. different at the edges.
One of the things that happens...
Hi All . . .
Cheers Peter . . .Have created a link to a folder with a couple of PDF's that may be useful . . .
https://www.dropbox.com/sh/m8g8g3r2u36kpg5/AABYCzdDj5f8oE4yOXJNm4X8a?dl=0
Please...
Hi All . . .
I have been watching a few of the threads lately and would like to try and help with some issues relating to the FT-S5000 & FT-S5500 . . Relating to MacOS versions, SCSI cards and...
Hi . . . The lamps are compatible. They are special ones that have a silver foil on one side to reflect light in a certain direction.
Hence when fitting them ensure the 'SCREEN' label is facing the...
Hi All . . .I received a reply from my colleague . . He stated that the Cezanne series ceased production in 2009, but they have to support parts until Aug.2016.
Therefore you should be able to...