Hi all
I’m starting a restoration of an old half plate camera and am struggling with removing some tiny wood screws that hold a brass fitting onto the body. I’m starting to damage the heads. Any tips/tricks for removal?
Thanks
John
Hi all
I’m starting a restoration of an old half plate camera and am struggling with removing some tiny wood screws that hold a brass fitting onto the body. I’m starting to damage the heads. Any tips/tricks for removal?
Thanks
John
John, If you don’t have a good set of screw drivers of various sizes it easy to destroy screw heads. Get a good set with long handles and good grips such as those made by Wiha. Small jewelers screw are difficult to grip and get good/proper torque. It is critical that the width of the blade and thickness match the screw head as close as possible. If the head is corroded away then there was another recent thread on how to remove screws with broken and damaged heads.
These same screw drivers are great for repairing shutters as well especially in the smaller sizes. The good thing about Wiha is that you can buy individual replacements screwdrivers as you damage or wear them out. This happened to me when I encountered a reverse threaded screw on a copal shutter. https://www.largeformatphotography.i...an-Ansco-8x10)
Last edited by OKAROB; 22-May-2024 at 13:44. Reason: Add link to thrread
Your options depend on the screw -- the size and shape of the head. Is it 1/8" or 1/2" wide? Is it slotted or phillips? Is it rounded or flat? Is it flush or raised? A picture is worth a 1,000 words -- you should know that by now.
You learn by doing
I have many tools for this
Left hand drill bits
Easy Outs also left hand
The wood is more important than the screws
IMHO
I buy screw's by the 100
eBay
By now
Trade Wars are brewing
Tin Can
Are you sure they are wood screws? Check the other side of the fitting. It's possible that they are machine screws with a "nut" on the other end.
Did you try solvent or penetrating oil? Not ideal on wood I know but a drop or two might do wonders.
Antique brass wood screws can be problematic and non-standardized. Sometimes you have to grind your own screwdriver tips to fit, or carefully file flats on round-head screws to allow a small plier jaw to bite. Natural mahogany oil can seep into there over the decades, or residual varnish oil, and act like a cement. Shellac might also be present and acting like glue, which can be softened with strong alcohol or by using a hea gun. Antique restoration specialists often encounter these kinds of problems.
Last edited by Drew Wiley; 22-May-2024 at 17:24.
Some methods that I have used in the past:
1. Heating the screw with the tip of a soldering iron then letting the screw cool down. Worked a few times.
2. Tried using a very small torch but always scorched or burned the wood around the screwhead - DO NOT TRY THIS.
3. Custom grinding down the tapered heads of screwdrivers making them non-tapered heads to exactly match the slots in the screwheads. Worked a lot of times.
4. Soaking the area around the screw with water. Never worked.
5. Put a drop of Aluminum Cutting Fluid on the screw and soak overnight. Seemed to work.
6. Drilling out the screw and replacing it with a slightly larger brass screw. Last resort but had to do this many times especially when the head of the screw broke off.
good luck
Thank you all for your comments and advice.
These are all standard screws. The Victorians kept it simple.
I do have a good set of small screwdriver bits but the handle is small so I can't get the leverage. I also have 3 turnscrews too but they're a bit too big. On other stubborn screws, I did find penetrating oil worked but not with these. Part of the problem I have is the difficult to remove screws aren't brass and have rusted. Greg, great suggestions, I'll give them a go. Pic of the offending screws below.
Bookmarks