Results 1 to 9 of 9

Thread: 8x10 film development

  1. #1

    Join Date
    Feb 2002
    Posts
    89

    8x10 film development

    After years of tray developing 4x5 film I wil be moving up to 8x10. Can I tray develop the same way with 8x10 as I do with 4x5? I use HC110 at 1:64 and develop 10-12 sheets at a time with a develpment time of 17 minutes (one minute for complete pass). Can I do maybe 5 sheets of 8x10 comfortably using the 1minute pass? Joel

  2. #2

    8x10 film development

    Joel, I develop 8x10s exactly the same way as 4x5s with one possible exception -- I usually develop just one negative at a time. I haven't gotten to the point where I can do more than one at a time, and in general I don't have so many to do... JDClark

  3. #3

    Join Date
    Feb 2002
    Posts
    89

    8x10 film development

    Thanks JD Clark. I have never developed one sheet of film before. I'm not sure I could match the agitation to get a predictable contrast. I will add 3 or 4 clear sheets,(I'm always develping unexposed film by mistake) of film to the batch so that I may stay with the 10 - 12 sheets I base my agitation time on. With 8x10, I may have to change my developing habits as I too won't be developing more than a few sheets at a time

  4. #4

    8x10 film development

    There is no reason why you should not be able to develop multiple sheets of 8x10 film in a tray. As mentioned earlier, you do need to figure out the correct amount of developer for the number of square inches of film to be developed. Or put another way, "How many sheets of film can be developed in (for example) 2 liters of developer?"

    You will need to test development times. I don't know if 4x5 emulsions and 8x10 emulsions are the same.

  5. #5
    Whatever David A. Goldfarb's Avatar
    Join Date
    Mar 2000
    Location
    Honolulu, Hawai'i
    Posts
    4,657

    8x10 film development

    My limit is 8 8x10" sheets per 11x14" tray with 2 quarts of chemistry, shuffling the stack once every 30 sec., but in practice, I rarely do more than 6 sheets in a batch. I guess I could do more if I were using a deeper tray and a film that liked to be shuffled once per minute. Start with fewer sheets and work your way up to be sure you're comfortable with it.

  6. #6

    Join Date
    Oct 2000
    Posts
    114

    8x10 film development

    Hi all, I always seem to get scratches when processing multiple sheets in a tray. So I just do one at a time. But for a lot of film, group processing sounds great if I can eliminate the scratching.

  7. #7

    8x10 film development

    With dip and dunk process I was never able to get even development when there were even tones over large portions of the negative - like the sky. I tried tray processing for a little bit but I hated the mess it made and I was always afraid that I'd pollute the developer with stop or fix - which makes this a very expensive one shot process.

    So I got a Unicolor drum and roller and life has been good. With 8x10 I can do just one sheet at a time, but after loading the film, everything else is in daylight. I use about 250 ml of developer solution which I throw away, insuring that the developer is consistent and the process repeatable. There isn't any mess and I get wonderful even tones in those skies!

    You are talking about doing a lot of film at one time and perhaps my way isn't feasible. But I'd hate to do all the shooting work and then mess up (scratches, uneven development & so on) by trying to process it all in a hurry. I also can do something else while the film is being machine agitated, so while I'm in the room, I don't have to sit there in the dark mindlessly rocking a try back and forth.

    One of the strengths of large format is to fine tune the process for each negative. I use kind of a soft zone (the only kind of zone that makes sense to me) and I mark my film holders to indicate flat lighting, or contrasty or whatever so I can tweak the development somewhat.

    I sure that for well under $200 ($100?) you could get a Unicolor roller and drum, and after you see the results I doubt if you'd go back.

  8. #8

    8x10 film development

    Joel,

    The answer is yes you can. We usually develop 8 sheets of 8x10 at a time, but I have often gone to 10 or 12. Keep agitation constant. I have found it impossible to get the negatives even when only one at a time is developed.

  9. #9
    Whatever David A. Goldfarb's Avatar
    Join Date
    Mar 2000
    Location
    Honolulu, Hawai'i
    Posts
    4,657

    8x10 film development

    The key to avoiding scratches and getting even results is to be sure to have enough chemistry--at least one quart or litre per four sheets in an 11x14" tray, and don't use a process that develops too quickly--more dilute solutions and lower tempertures are to your advantage in this regard.

    When inserting the sheets into the fluid, don't insert edge first. Pass the sheet in from the front of the tray to the back in a sweeping motion with the leading edge bent up slightly, then pat the sheet down with your fingertips.

Similar Threads

  1. Highly Dilute Paper Negative Development for 8x10?
    By Michael Heald in forum Darkroom: Film, Processing & Printing
    Replies: 8
    Last Post: 5-Dec-2005, 02:02
  2. Developing my first 8x10 - stand development
    By Paul Cutler in forum Darkroom: Film, Processing & Printing
    Replies: 15
    Last Post: 30-Aug-2005, 09:48
  3. Uneven development of 8x10 negs in C-41
    By JanE in forum Darkroom: Film, Processing & Printing
    Replies: 8
    Last Post: 22-May-2004, 04:09
  4. Film development times for Kodak's new 320Tri-X sheet film?
    By Fred Ullrich in forum Darkroom: Film, Processing & Printing
    Replies: 1
    Last Post: 29-Dec-2003, 10:56
  5. My first 8x10 film development
    By Cecil Pang in forum Darkroom: Film, Processing & Printing
    Replies: 11
    Last Post: 19-Sep-2003, 17:30

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •