Results 1 to 6 of 6

Thread: enlarger alignment

  1. #1

    Join Date
    Mar 2001
    Location
    Seattle
    Posts
    632

    enlarger alignment

    Hi folks,

    Just wondering if someone has a good procedure for enlarger alignment, without t he use of that special tool sometimes used for aligning Omega enlargers. Thanks!

    Chris

  2. #2

    enlarger alignment

    Chris: Here is the method I have used for years and it works with no problems whatsoever: First, get a small level and level the enlarger baseboard on the table, side to side and front to back. Use wood or cardboard shims to get the baseboard level. Second, insert an 8x10 sheet of glass into the negative stage and lower the head to hold the glass tightly. You may want to tape the edges of the glass to protect yourself. Lay the level on the glass and level the negative stage side to side and front to back. Then place the level across the lens flange and level the lens stage. Recheck all, and the enlarger should be in good alignment. Now take a fine tip felt tip black pen and draw lines either on the piece of glass or a clear negative from side to side, front to back and corner to corner. Now place the glass or negative in the enlarger and check the focus with the lens wide open. It should now be sharp overall. You may need to stop down to bring the corners into sharp focus, depending on the lens. If the corners are slightly soft with the lens wide open, they should be equally soft at all four corners. This should do the trick for you.

    Regards,

  3. #3

    enlarger alignment

    I haven't set up my 4x5 enlarger yet--still cleaning the basement, but when I had a Beseler 23C II, I put a piece of graph paper in a negative carrier and projected that on to the baseboard and measured the distance between the lines. If the top and bottom distances were the same and the left and right side distances were the same, I considered it aligned. I put a negative in to check and found all four corners and the middle in focus.

    Dave

  4. #4

    enlarger alignment

    The Peak focuser (model 2000, which allows to check the focus in the corners) is, in my opinion, a simple and efficient way of aligning enlargers. The enlarger is properly aligned if the grain of the emulsion is simultaneously sharp in the four corners. The advantage of this method is that it relies directly on the most important criteria of alignment: sharpness throughout the entire surface of the negative. Moreover, it also gives information on the quality of the enlarging lens at the chosen working aperture; field curvature is, for instance, evident if the four corners, on the one hand, and the center, on the other hand, are not simultaneously sharp. I have, for instance, two samples of the same enlarging lens (105 mm rodagon) and I discovered, using the Peak focuser, that they were quite different, wide open, in term of field curvature. Another advantage of this solution is that it does not involve an additional gadget since a grain focuser is anyhow essential. One should lastly note that the Peak (all metal) is a much nicer object than the usual all plastic grain focusers.

    regards, Matthieu

  5. #5

    Join Date
    Dec 1999
    Posts
    32

    enlarger alignment

    Another contributor to these pages describes a procedure using two mirrors in this document:

    http://members.rpa.net/~choffman/darkmeasure.htm

    I haven't made the mirror with the hole in it yet but it looks like the method should work quite well.

    Cheers,

    Duane

  6. #6

    enlarger alignment

    Hi, I have had good luck with the laser method. The real surprise was finding large differences between easels. Some of these were greater than any enlarger alignment problems. Don't forget to check these rascals Dick

Similar Threads

  1. alignment w/negatrans
    By Richard Schlesinger in forum Darkroom: Equipment
    Replies: 1
    Last Post: 20-Jul-2005, 11:22
  2. Omega D5 alignment
    By Todd Joseph in forum Darkroom: Equipment
    Replies: 5
    Last Post: 28-Jan-2005, 14:48
  3. alignment on Beseler MCRX
    By michael franc in forum Darkroom: Equipment
    Replies: 8
    Last Post: 26-Mar-2002, 13:27
  4. Saunders 4550XLG enlarger. Can its alignment be improved?
    By scott jones in forum Darkroom: Equipment
    Replies: 3
    Last Post: 20-Nov-2001, 18:05
  5. Alignment finder for enlarger
    By sugi sugi in forum Darkroom: Film, Processing & Printing
    Replies: 5
    Last Post: 21-Jul-2000, 20:23

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •