Results 1 to 5 of 5

Thread: N+ and N- times for Pyro

  1. #1

    N+ and N- times for Pyro

    I am currently developing 4x5 negatives of Tri-X Pro Pan (rated at 200) and Ber gger Pan (rated at 100) in the Leban ABC Pyro formula in a Jobo Expert Drum. No rmal development runs between 7-1/2 minutes and 8 minutes. I would appreciate an y suggestions regarding N+ and N- times for these films. Thank you.

  2. #2

    Join Date
    Mar 2000
    Posts
    50

    N+ and N- times for Pyro

    Mark

    You say that you are using Tri-X Pro Pan by which I take it that you are using the Tri-X nominally rated at 320 by Kodak. If this is the case then, depending on the type of photography you do, there could be some significant pitfalls. Unless this film has been redesigned and reformulated it is recommended for studio use only, and if used outdoors could offer some serious problems depending on the lighting conditions. Most people buy the pro films because of the short dating and and what is supposed to be optimum aging. The fact is that Tri-X professional is designed for studio use in extremely controlled lighting conditions, and it has no anti-halation backing. Used outdoors on bright, or even cloudy bright days, there can be significant light scattering in the emulsion which can impact your controlled development and contrast methods. Having said that, I have used the film for many years and like it a lot, but I do not consider it to be the best film for many lighting conditions. There is also the possibility that the film you are testing is different from what was previously available to me. In that case you are on your own here and I wish you the best of luck. I know absolutely nothing about Bergger film, so I am an empty fountain of knowledge there. See if you can get some Kodak Ektapan (ei 100) and try that out. I used this film a lot and really liked it. Don't remember how I rated it because I quit using light meters many years ago. Find a film/developer combination you like (and I used D-23 split and loved it) and stay with that.

  3. #3

    Join Date
    Sep 1998
    Location
    Oregon and Austria
    Posts
    2,300

    N+ and N- times for Pyro

    Mark,

    Don't concern yourself too much with the alluded to inflexibility of Tri-X in 4x5 size. Ansel Adams and countless other photographers of merit (myself modestly included) use(d) Tri-X Pro 4x5 outdoors, (which, incidentally, is not the same film as Tri-X Pro in roll film formats), with excellent results. If you understand your film/developer characteristics, you can use it under just about any lighting condition. Tri-X has proved itself to be a great "general- purpose film" (to quote Kodak). As to your original question, I can only say that the individuality of approach and equipment combinations precludes any definitive determination of N+ or N- times. You need to test for yourself. If you don't have a densitometer (I don't either) I suggest you get a copy of "The New Zone System Manual" by Minor White, Richard Zakia, et al. and review their suggestions for Zone system calibration. I have found this approach to be quite accurate, useful and quick once you get the hang of it. Regareds, ;^D)

  4. #4

    Join Date
    Dec 1999
    Posts
    195

    N+ and N- times for Pyro

    Mark, The preceding comment by Doremus Scudder is the best advice. Test for N- and N+ yourself.Recall that you cannot easily use a densitometer to interpret the results due to the staining. However, some writers suggest that Tri-X and other films of its type,meaning non T-Max or Delta, require for N+ a 30-40% increase in normal film development time + plus a 1/2-1 stop decrease in exposure. For N-1 the development time , the normal development time should be reduced by 30-40%, and the exposure increased by one stop. Gordon Hutchings suggests the following for Tri-X: (N=14 min), (N+1=20 min.), (N-1=11 min). But that is assuning an E! of 260 AND the use of his PMK developer. Hope this helps. Bob

  5. #5

    N+ and N- times for Pyro

    I have tested HP-5 plus for the zone system with D-23 and D-25. With both developers, each change of 1 zone in development needed a 1/3 stop change in exposure: N-1 needs 1/3 stop more than N; N+1 needs 1/3 stop less than N. N-1 required a 15% reduction in developing time, N-2 required a 30% reduction, and N+1 required a 60% increase. You might use these (or Bob's) suggestions as a guide.

Similar Threads

  1. Developing times for Fuji Acros film with rollo Pyro?
    By Robert Brummitt in forum Darkroom: Film, Processing & Printing
    Replies: 0
    Last Post: 7-Oct-2003, 16:58
  2. T Max RS 1:9 @ 70` Any Times for TMY???
    By Dave Jarosz in forum Darkroom: Film, Processing & Printing
    Replies: 2
    Last Post: 4-Jun-2002, 22:06
  3. comparison of Pyro and Pyro type developers
    By chris kargoris in forum Darkroom: Film, Processing & Printing
    Replies: 12
    Last Post: 25-Aug-2001, 12:39
  4. Developing times for Bergger BPF 200 and HP5 in Rollo-Pyro
    By Gudmundur Ingolfsson in forum Darkroom: Film, Processing & Printing
    Replies: 2
    Last Post: 28-Jul-2000, 10:23
  5. T-Max 100 at EI 64, what are the times?
    By Brian Bullen in forum Darkroom: Film, Processing & Printing
    Replies: 2
    Last Post: 1-Oct-1999, 02:05

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •