Results 1 to 7 of 7

Thread: Film Developing in a Jobo Tank

  1. #1

    Join Date
    Dec 1997
    Location
    Seattle, Washington
    Posts
    67

    Film Developing in a Jobo Tank

    Hi,

    Somewhere I once read that, when using a tank to develop film, you should always make sure that the tank was full of film to capacity. That is, if your tank ho lds six sheets, but you only have four to develop, then you should add two unexp osed sheets to the tank.

    If this is true, why?

    Does it matter if you mix films (i.e. Tri-X and Tmax) when developing Tri-X? I can't see why it would.

    Thanks, Robert

  2. #2

    Join Date
    Mar 2000
    Posts
    72

    Film Developing in a Jobo Tank

    I regularly process 1 or 2 sheets of film in a Jobo expert tank. I rarely fill the tank to capacity with film. I have never had a problem with consistency, uneven development, or anything else.

    I do not process different emulsions together primarily because the emulsions I use require different processing times.

    -Bill

  3. #3

    Film Developing in a Jobo Tank

    The second to last studio I worked with had three JOBO units, one for each process, and a 4th back-up. They would regularly shoot three shot tests and then process all three in the same drum to check exposure, etc.

  4. #4

    Join Date
    Apr 2000
    Location
    Calgary
    Posts
    308

    Film Developing in a Jobo Tank

    For reason of consistency, you may wish to always have about the same amount of exposed film emulsion in the same amount of developer. For that purpose, one sheet of fully exposed film (out of the camera) equals two sheets of in-camera exposed film. (courtesy John Sexton workshop).

    I have a small stack of outdated or wasted sheets at hand in the darkroom, to add to my developing tank if necessary.

  5. #5

    Film Developing in a Jobo Tank

    If you use enough developer per sheet, you will not need to do this. I use 500ml of D-76 1:1 (or equivalent) per 8x10 sheet, in accordance to The Film Developing Cookbooks instructions. At this rate, I can only develop two sheets at a time.

  6. #6

    Film Developing in a Jobo Tank

    I've had pretty bad experiences trying to use the Jobo tanks for 5x4 cut film. In fact Jobo contradict themselves in the instructions for the 2509 cut film adapter.The advertising blurb stated that you could fit 6 sheets into each adapter, and indeed there are six slots in the 2509. However, the instructions that come with the 2509 say that no more than 4 sheets should be developed in it at any one time.The problems I've experienced have been 'tide' marks and foaming marks. The foaming marks were obviously caused by air bubbles trapped between sheets of film that were too close together.

  7. #7

    Film Developing in a Jobo Tank

    Note that the latest 4x5 reel from Jobo is the 2509n. The "n" model comes with plastic "panels" that snap onto the reel after the film is loaded to keep the sheets in place and improve agitation consistency. I recall Jobo admitting somewhere (check the Jobo Quarterly on the Jobo web sites) that the original 2509 had problems. I've seen no agitation problems at all with my 2509n. If you are having problems with the 2509, I'd recommend upgrading to the 2509n.

    (Also, if you're looking for the 4x5 reels used, like on eBay, be sure that you know which you're getting.)

Similar Threads

  1. 8x10 sheet film with D-76 in Jobo 3005 tank
    By Phong in forum Darkroom: Film, Processing & Printing
    Replies: 3
    Last Post: 4-Aug-2005, 06:04
  2. JOBO 2500 4X5 sheet film processing tank
    By john_679 in forum Darkroom: Film, Processing & Printing
    Replies: 9
    Last Post: 8-Dec-2003, 01:15
  3. Need a source for 5x7 film developing tank
    By octagon in forum Darkroom: Film, Processing & Printing
    Replies: 4
    Last Post: 8-Oct-2001, 16:38
  4. JOBO Sheet Film Tank System
    By mario abba in forum Darkroom: Film, Processing & Printing
    Replies: 10
    Last Post: 12-Jun-2001, 19:09
  5. Developing 4x5 Film by Inversion in a Jobo Tank 2500
    By Amine SULTAN in forum Darkroom: Film, Processing & Printing
    Replies: 6
    Last Post: 28-Nov-1999, 23:07

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •