Results 1 to 7 of 7

Thread: Flash - how to factor fl of lens into equation

  1. #1

    Flash - how to factor fl of lens into equation

    I have always used this formula for 35mm electronic flashes

    GN/fstop x sqrt. (ASA/100) = distance

    However, this formula does not take into consideration the fl lens being used... or the fl setting on the flash either. The formula assumes you enter the prope r GN for the fl lens you plan to shoot with (and also the equiv. fl setting on t he flash). Therfore when a Guide Number is quoted, it assumes a specific lens f l, some flash makers use 50mm and others like Cannon are more aggressive and use their high end zoom fl's, like 105mm. Some manuals produce tables showing the different GN's at each zoom level. However if I want to add a fresnel in front of the flash to decrease its angle of coverage to that equal to a 300mm lens, th en how do I figure out the new GN for that flash at 300mm vs. say 105mm? I coul d not find a relationship between GN and fl in the manuals... for example, at 35 mm fl the GN = 35, but at 105mm the GN = 54? I have never seen a formula take t he lens fl (or angle of coverage) into account? Can anyone introduce this varia ble into the formula?

    I realize for LF I would simply convert the 35mm to LF equivalents ... but to k eep this question simple, lets just treat it as a 35mm issue. Any input would b e helpful.... Thank you in advance...

  2. #2

    Join Date
    Sep 1998
    Location
    Buford, GA
    Posts
    13,172

    Flash - how to factor fl of lens into equation

    Please go and talk to Wayne.

    A guide numebr is simply a starting point. If you want a more accurate method of determining the exposure with flash then you need the BCPS or the ECPS and the angle that the number is given for. The BCPS and ECPS are based on flash coverage over a specific angle. They convert into a GN or a F stop.

  3. #3
    Whatever David A. Goldfarb's Avatar
    Join Date
    Mar 2000
    Location
    Honolulu, Hawai'i
    Posts
    4,657

    Flash - how to factor fl of lens into equation

    Or better yet, just make your own tests.

    Each reflector, fresnel, diffuser, or other attachment to the flash, or change in power output (focal length setting on the flash unit in your case) changes the guide number. For a few years, before I could afford a decent flashmeter, I determined exposure for 2- and 3-strobe portrait and copy setups with nothing but a tape measure, paper and pencil, and guide numbers I'd determined objectively on film by bracketing exposures of a grey card and a scene with a variety of tones. It's somewhat labor intensive first time around, and it means planning all studio shots in advance, but that's not such a bad thing anyway, and I don't think I've ever made a wrong exposure in this way (which is not to say that I've never made an exposure error, just not by this method).

  4. #4
    Whatever David A. Goldfarb's Avatar
    Join Date
    Mar 2000
    Location
    Honolulu, Hawai'i
    Posts
    4,657

    Flash - how to factor fl of lens into equation

    Rereading your initial post...

    The actual focal length of the lens does not really matter, as long as the f-stops are accurately marked. The "focal length" setting on your flash unit is just a suggestion and is really a representation of the power setting of the flash. Some flash units mark this as a fraction of the maximum power of the unit, others in watt-seconds.

    Once you determine the exposure for a particular flash-to-subject distance, you can change lenses all you want, and the exposure should be the same.

  5. #5

    Flash - how to factor fl of lens into equation

    Thank you for the responses... I kind of left out one part of the situation... I was trying to calc. the new GN because I did not have the fresnels to accomplish a 300mm lens (or respective angle of coverage)

    I agree with Bob about the BCPS, but I can not find that listed in the manuala? And assuming I find it, I still do not have the formula.

    To clarify why the fl is a factor on these small electronic flahses... when you change the fl setting on the flash, (or on thelens, which autmaticlly changes it on the flash in TTL mode) it increases or decreases the angle of coverage to accomodate the part of the scene that lens will see on film. So at the same subject distance, the flash set at 35mm fl, will yield a 35 GN, while at 105mm fl setting, it will produce a GN of 54... meaning more light can be directed at the subject because the angle of coverage has been reduced.

  6. #6

    Join Date
    Mar 1998
    Posts
    1,972

    Flash - how to factor fl of lens into equation

    Bill you are asking about the coverage of a variable focus flash, which is neces sarily independent of the focal length of the lens on the camera. Camera lens focal length plays no role in determining how the GN of your flash.

  7. #7

    Flash - how to factor fl of lens into equation

    Ellis, I realize the lens setting is independent of the fl setting on the flash.... however, the fl setting on the flash determines the GN. When a flash is advertised to be 100 GN, that assumes a certain setting fl setting (or zoom) on the flash. As the fl setting becomes higher, the guide number increases because light is directed in a smaller area of coverage. Most flash manuals give the different guide numbers for each of the fl settings on the flash... for example CAnnon 540's go from 24mm - 105mm. But what I wanted to know, is how do I calc. what the GN would be at 300mm. The manual does not show this because the flash does not go past a 105mm setting. Am I explaining it better now?

Similar Threads

  1. Depth of Field + Lens Size + Enlargement Factor
    By Ken Lee in forum Lenses & Lens Accessories
    Replies: 13
    Last Post: 17-Jul-2004, 09:35
  2. Replies: 6
    Last Post: 13-Oct-2003, 11:19
  3. Exposure Factor Needed with Diopter Closeup Lens?
    By Alan Davenport in forum Style & Technique
    Replies: 3
    Last Post: 31-May-2002, 17:52
  4. Replies: 4
    Last Post: 2-May-2001, 22:43
  5. Lens to subject distance formulae for known magnification factor and fl?
    By Bill Glickman in forum Lenses & Lens Accessories
    Replies: 1
    Last Post: 29-Jan-2000, 22:28

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •