Tachihara 11x14 holders? Any reviews? Any comments? Why so expensive?

[Torontoamateur]

I am thinking of purchasing new 11x14 holders for my Wisner 11x14. But the Tachihara are so expensive. I mean they re gorgeous and wonderful, But the price is shocking. Why are they so expensive ? are they worth the price?

[Tin Can]

Looked the price up

Normal

Mine were custom made by Richard Ritter https://www.lg4mat.net/filmholder.html 8 years ago

[Tin Can]

I made a simple 11X14 film holder years ago and documented it in DIY
Black Matt Board to any size, no complication

Double stick tape, with clear plastic a bit thicker than film to fit the Dims outside

Another piece of same tape and same plastic overlapping the first rail for film containment

Covered with Black Gaff Tape

No DS need on my setup

Made it twice, first was 10X16 with 2 pieces of 8X10

I prefer 11X14

It works very smoothly

Dark Slide could be stacked

11X14 Film Holder DIY by TIN CAN COLLEGE, on Flickr

[Oren Grad]

I had some Tachihara 11x14 holders for a while. They were nicely made, but the septum seemed spring-loaded, requiring downward pressure on the film during insertion. The required combination action of threading such a large and floppy sheet of film under the retaining flanges in the dark and sliding the film in while exerting downward pressure made loading a royal pain. I sold the Tachiharas and now have a mix of Fidelity and S&S holders in that size.

[Torontoamateur]

How about this as an alternative? https://www.ebay.com/itm/32534723287...AaAv0HEALw_wcB

I am not sure of the dimensions of the holders or the light leak situation. It is too experimental. I bought two wooded before and found the raised rail to hold the unit in place as in the wrong spot Still not yet fixed I would not sell becausee it is so wrong That is when I stopped buying unknown manufacturer. They get the dimensions wrong and then the holders will not fit or will fail or the film plane is not aligned in focus.

[Torontoamateur]

I had some Tachihara 11x14 holders for a while. They were nicely made, but the septum seemed spring-loaded, requiring downward pressure on the film during insertion. The required combination action of threading such a large and floppy sheet of film under the retaining flanges in the dark and sliding the film in while exerting downward pressure made loading a royal pain. I sold the Tachiharas and now have a mix of Fidelity and S&S holders in that size.

I bought them and will find out in about a week Wish me luck!!

[Torontoamateur]

I made a simple 11X14 film holder years ago and documented it in DIY
Black Matt Board to any size, no complication

Double stick tape, with clear plastic a bit thicker than film to fit the Dims outside

Another piece of same tape and same plastic overlapping the first rail for film containment

Covered with Black Gaff Tape

No DS need on my setup

Made it twice, first was 10X16 with 2 pieces of 8X10

I prefer 11X14

It works very smoothly

Dark Slide could be stacked

11X14 Film Holder DIY by TIN CAN COLLEGE, on Flickr

Looks flimsy I will stick to well made produced by reliable camera makers.

[cuypers1807]

I use Chamonix 11x14 holders and they are excellent.

[Tin Can]

If you got the money honey and the time

I installed my simple and cheap DIY into free 12X15" Copy Camera holders. of course I used the free camera too

It is heavy as can be, but very good for some things

Looks flimsy I will stick to well made produced by reliable camera makers.

[Oren Grad]

I bought them and will find out in about a week Wish me luck!!

Good luck!