Page 2 of 2 FirstFirst 12
Results 11 to 13 of 13

Thread: [Newcomer] How should I measure exposure for nighttime portraits?

  1. #11
    jim_jm's Avatar
    Join Date
    Jan 2013
    Location
    San Diego, CA
    Posts
    120

    Re: [Newcomer] How should I measure exposure for nighttime portraits?

    1. I usually meter average caucasian skin tones at Zone V or VI. It shouldn't be much different regardless of the light source, it's the amount of exposure that the film receives that is important.
    2. It's not possible to predict what shutter and aperture settings to expect, given that the intensity of artificial lights and distance from the subject will vary greatly. If your main light source is the setting sun, streetlights, lamps, candles or otherwise, that will be the main determinant of your exposure settings, along with your film speed. The rule of "Sunny-16" for daylight exposures is only possible given that the luminance of the sun at certain latitudes and times of day is a known factor. Correct exposure becomes very difficult to predict with artificial light sources and at night, until you start taking meter readings of your subject.
    3. You can add light to the subject without having it look too artificial or resorting to strobe flash. This may let you use shorter shutter speeds and/or smaller apertures. It's a big can of worms and there's lots of options available.
    4. Exposure compensation for bellows extension is always a factor to consider. As you focus on a closer subject, you need to extend the bellows to get a sharp image. This means the lens is further from the film and the intensity of the light hitting the film is fainter. This is where a tape measure comes in handy. First set up your camera in daytime and focus on a distant object more than a few hundred feet away. Measure the distance from the lens board to your film plane and this will be your infinity focus distance for this lens. It should be approximately equal to the focal length of the lens, say 180mm (or 7"). To focus on objects that are closer, you'll need to extend the bellows. A general rule I use is to add one stop exposure for every 50% of bellows extension. So if my 180mm lens has been focused on a close subject and it measures 270mm from the film (an extra 50% or 90mm), I would add an additional stop of exposure (either slower shutter speed or larger aperture). If the subject was not so close and the bellows measured 225mm (an extra 25% or 45mm) then add only 1/2 stop exposure.

    Low-light exposures with large format can be tricky. You're generally using slower shutter speeds and most lenses are not very fast. Your shutter speeds may be very slow so your subject will need to hold still. Mistakes will be more expensive per shot also. Personally, I'd try this with 35mm or medium format as the lenses are faster and the cost per shot is much less.

    Here's an example of a shot I took in low light and while not really a people portrait, the metering situation was similar to what you are describing.
    - Interior shot, both carousel horses illuminated by spotlights from above.
    - The shadows were very dark so I spot metered off the horses' heads only. With the black one I was careful to avoid the silver headpiece (will influence the meter), and put it at about Zone III. With the lighter background horse I metered at about Zone VI.
    - This was taken on 35mm, handheld but braced against a chair, and I think the exposure was about 1/8 sec at F:2 on ISO 400 film. The negative looks underexposed, but it printed very easily in the darkroom.

    Click image for larger version. 

Name:	Museum_displayl.jpg 
Views:	22 
Size:	21.9 KB 
ID:	230142

  2. #12

    Join Date
    Dec 2005
    Location
    El Pueblo de Nuestra Señora la Reina de los Ángeles de Porciúncula
    Posts
    5,480

    Re: [Newcomer] How should I measure exposure for nighttime portraits?

    I’m surprised that the old-timers haven’t mentioned this… perhaps they forgot or never used this technique.

    The white side of the gray card had a use for exposure determination in the days before it became primarily used for white balance on digital cameras! This usage doesn’t seem to have been mentioned for decades. See the section on exposure determination in dim light:

    https://www.scantips.com/lights/kodakgraycard.pdf

  3. #13
    Tin Can's Avatar
    Join Date
    Dec 2011
    Posts
    20,146

    Re: [Newcomer] How should I measure exposure for nighttime portraits?

    "...For this reason, it is generally
    easier to make an extra negative with the card at the center of interest. ...
    Tin Can

Similar Threads

  1. Nighttime is the right time!
    By Audii-Dudii in forum Image Sharing (Everything Else) & Discussion
    Replies: 66
    Last Post: 17-May-2022, 11:36
  2. Long exposure experience with portraits?
    By Ulophot in forum Style & Technique
    Replies: 23
    Last Post: 10-Apr-2020, 09:11
  3. Replies: 23
    Last Post: 27-Sep-2019, 15:39
  4. Nighttime LF questions
    By Kirks518 in forum Style & Technique
    Replies: 4
    Last Post: 6-Jul-2015, 10:16
  5. Nighttime meter reading for 8x10's
    By Sean McDonough in forum Style & Technique
    Replies: 4
    Last Post: 13-May-2002, 17:00

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •