Results 1 to 7 of 7

Thread: Printing Glass Plates: How to avoid breakage?

  1. #1

    Join Date
    Jul 2005
    Location
    Tel Aviv
    Posts
    439

    Printing Glass Plates: How to avoid breakage?

    Hello,

    I'm in the process of preparing to print some 80-100 year old glass plates, and wanted to ask folks with experience how they print them. I plan to use azo/lodima, and am worried a heavy piece of glass which I normally use may break these old plates. If I use single-weight paper, are there any good alternatives to applying pressure, or is that really the only way? ANy of you have bad experiences you'd like to tell me about? These are small, from 5x7 down to somewhat smaller than 4x5. Thanks.

  2. #2

    Join Date
    Aug 2000
    Location
    California
    Posts
    3,908

    Re: Printing Glass Plates: How to avoid breakage?

    I use them in place of the glass in an old fashioned contact printing frame. No breakage so far.

  3. #3

    Join Date
    Jul 2005
    Location
    Tel Aviv
    Posts
    439

    Re: Printing Glass Plates: How to avoid breakage?

    Hi Jim,

    Not sure I understand you, do you mean you remove the glass from the contact frame and then use a glass plate without a top glass? If so, what exerts the pressure needed for good contact?

  4. #4

    Join Date
    Oct 2015
    Posts
    1,573

    Re: Printing Glass Plates: How to avoid breakage?

    I would try simply laying the glass plate on the paper. I've done this for proof prints to be filed with the glass plate, but have yet to attempt a fine print from one. If some pressure becomes necessary, I can't imagine that gently laying a piece of plate glass on the plate to be printed would cause it to break; especially if the plate glass is the same size. But, please, do what you think best as it sounds like you have irreplaceable plates.

  5. #5

    Join Date
    Apr 2009
    Location
    Seattle area, WA
    Posts
    1,328

    Re: Printing Glass Plates: How to avoid breakage?

    Quote Originally Posted by G Benaim View Post
    Hi Jim,

    Not sure I understand you, do you mean you remove the glass from the contact frame and then use a glass plate without a top glass? If so, what exerts the pressure needed for good contact?
    The spring at the back of the contact frame would exert pressure this way- but the caveat is the frame's rebate for glass needs to be the same as your negative- which is likely an issue. You can use a regular contact printing frame with the glass still intact too, it's a bit riskier I suppose but commonly done.

  6. #6
    Vaughn's Avatar
    Join Date
    Jan 2007
    Location
    Humboldt County, CA
    Posts
    9,211

    Re: Printing Glass Plates: How to avoid breakage?

    Quote Originally Posted by Jim Noel View Post
    I use them in place of the glass in an old fashioned contact printing frame. No breakage so far.
    I use some contact printing frames from B&S. I use an piece of black matboard for normal printing -- seems to have more space for printing glass plates than others I have used.

    Another option would be a vacuum easel (different from a vacuum frame...no glass) that would hold the paper completely flat, then use just the weight of the glass plate itself to lay tight against the paper.

    OR...use soft foam below the paper, put the glass neg on top, then glass over that. The foam would allow for minimal pressure against the neg and still make good contact.

    With the age of your plates, I would inspect them carefully for defect in the glass -- especially on the edges. I have never had the glass of the frames break during use, but it has been newer glass with sanded edges that would be less likely to break under stress.
    "Landscapes exist in the material world yet soar in the realms of the spirit..." Tsung Ping, 5th Century China

  7. #7

    Join Date
    Aug 2000
    Location
    California
    Posts
    3,908

    Re: Printing Glass Plates: How to avoid breakage?

    Quote Originally Posted by G Benaim View Post
    Hi Jim,

    Not sure I understand you, do you mean you remove the glass from the contact frame and then use a glass plate without a top glass? If so, what exerts the pressure needed for good contact?
    Yes. The spring back exerts the pressure needed.

Similar Threads

  1. Contact printing glass plates...?
    By Randy in forum Darkroom: Film, Processing & Printing
    Replies: 18
    Last Post: 1-Dec-2020, 14:52
  2. Printing J Lane Dry Plates
    By Alan9940 in forum Darkroom: Film, Processing & Printing
    Replies: 4
    Last Post: 14-Aug-2020, 17:23
  3. How to avoid dribble/drooling from glass bottles?
    By m00dawg in forum Darkroom: Film, Processing & Printing
    Replies: 6
    Last Post: 9-Apr-2019, 20:51
  4. Printing from Plates
    By bob carnie in forum Darkroom: Film, Processing & Printing
    Replies: 0
    Last Post: 15-Nov-2013, 09:50
  5. Printing and proofing glass plates
    By Eric Woodbury in forum Darkroom: Film, Processing & Printing
    Replies: 4
    Last Post: 6-Nov-2010, 16:38

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •