Results 1 to 8 of 8

Thread: Traditional Wet Plate Sizes & Holders

  1. #1
    Tin Can's Avatar
    Join Date
    Dec 2011
    Posts
    22,385

    Traditional Wet Plate Sizes & Holders

    I have three LN Dry Plate DDS 3-1/4 X 5-1/4" Pat. 1894 Eastman Kodak

    And finally got a camera to match, it needs some work, it can be fixed by me

    I would assume Dry Plate sizing came from Wet Plate sizes

    I have been collecting film and plate holders for a while

    How long would one of these last, the septum is paper board, perhaps when that goes, I can make it one sided with a plastic septum

    I may not use these, but have assorted others just like it in different sizes

    I have NOT seen any old wet plate holders FS or in odd sizes

    Dry Plate Holder 1 by TIN CAN COLLEGE, on Flickr
    Tin Can

  2. #2
    Foamer
    Join Date
    Oct 2010
    Location
    South Dakota
    Posts
    2,430

    Re: Traditional Wet Plate Sizes & Holders

    That is postcard size, kind of an odd format. No idea how long it will last but the holders I've been using for about the past year are still in good shape. I clean out any dampness after each shot.


    Kent in SD
    In contento ed allegria
    Notte e di vogliam passar!

  3. #3

    Join Date
    Jun 2017
    Location
    West Coast
    Posts
    2,132

    Re: Traditional Wet Plate Sizes & Holders

    Quote Originally Posted by Tin Can View Post
    I have three LN Dry Plate DDS 3-1/4 X 5-1/4" Pat. 1894 Eastman Kodak

    And finally got a camera to match, it needs some work, it can be fixed by me

    I would assume Dry Plate sizing came from Wet Plate sizes

    I have been collecting film and plate holders for a while

    How long would one of these last, the septum is paper board, perhaps when that goes, I can make it one sided with a plastic septum

    I may not use these, but have assorted others just like it in different sizes

    I have NOT seen any old wet plate holders FS or in odd sizes

    Dry Plate Holder 1 by TIN CAN COLLEGE, on Flickr
    As Kent suggests, the life of that holder will largely be determined by how fastidious you are in mopping up and silver nitrate that comes in contact with the wood/cardboard.

    There are two main reasons to wipe out the interior of the plate holder after making each plate: to preserve the plate holder itself (AgNO3 is highly corrosive and will eat wood if allowed to accumulate), and to ensure that the next plate you make does not come in contact with a lot of contaminated silver nitrate from the previous plate. Why? Because silver nitrate left in the plate holder is what is responsible for much of the unwanted veiling artifacts that can happen. Its almost unavoidable that you will experience some of that, but if you don't wipe out the holder after each plate, you will get some serious contamination that will make a big mess on the plate.

  4. #4
    Tin Can's Avatar
    Join Date
    Dec 2011
    Posts
    22,385

    Re: Traditional Wet Plate Sizes & Holders

    Any ideas on a poly? coating I could apply all over these holders to slow degradation

    Quote Originally Posted by paulbarden View Post
    As Kent suggests, the life of that holder will largely be determined by how fastidious you are in mopping up and silver nitrate that comes in contact with the wood/cardboard.

    There are two main reasons to wipe out the interior of the plate holder after making each plate: to preserve the plate holder itself (AgNO3 is highly corrosive and will eat wood if allowed to accumulate), and to ensure that the next plate you make does not come in contact with a lot of contaminated silver nitrate from the previous plate. Why? Because silver nitrate left in the plate holder is what is responsible for much of the unwanted veiling artifacts that can happen. Its almost unavoidable that you will experience some of that, but if you don't wipe out the holder after each plate, you will get some serious contamination that will make a big mess on the plate.
    Tin Can

  5. #5

    Join Date
    Jun 2017
    Location
    West Coast
    Posts
    2,132

    Re: Traditional Wet Plate Sizes & Holders

    Quote Originally Posted by Tin Can View Post
    Any ideas on a poly? coating I could apply all over these holders to slow degradation
    John Coffer has instructions in his Doer's Manual for protecting and sealing the interior of a Brownie Box camera, using Polyurethane. So yes, it can be done. I did it to my Brownie 3B, but it needed a month to dry completely before I could make plates in it, without contaminating the collodion with whatever was still outgassing from the Polyurethane. So yes, it works, but expect to have to let it dry several weeks before you can use it. YMMV of course.

  6. #6
    Tin Can's Avatar
    Join Date
    Dec 2011
    Posts
    22,385

    Re: Traditional Wet Plate Sizes & Holders

    Thanks Paul, I read more on Poly and nobody thinks Poly on wood lasts, unless it is bar top thick

    I am going to convert 4X5 Graphic Film Pack Holder, it's almost all metal and fit's many cameras
    Tin Can

  7. #7

    Join Date
    Jun 2017
    Location
    West Coast
    Posts
    2,132

    Re: Traditional Wet Plate Sizes & Holders

    Quote Originally Posted by Tin Can View Post
    Thanks Paul, I read more on Poly and nobody thinks Poly on wood lasts, unless it is bar top thick

    I am going to convert 4X5 Graphic Film Pack Holder, it's almost all metal and fit's many cameras
    I have a traditional style 5x7 film holder (cannot recall what brand) that I was able to convert into a wet plate holder by pulling the septum out of the middle, and epoxying triangles of polycarbonate plastic to each of the four corners to support the plate. That was all I had to do to modify this particular film holder to use for wet plate - it was very simple. Look for a film holder with a metal septum that can be pulled out with strong pliers.

  8. #8
    Tin Can's Avatar
    Join Date
    Dec 2011
    Posts
    22,385

    Re: Traditional Wet Plate Sizes & Holders

    Got it, no problem

    Thank you

    Quote Originally Posted by paulbarden View Post
    I have a traditional style 5x7 film holder (cannot recall what brand) that I was able to convert into a wet plate holder by pulling the septum out of the middle, and epoxying triangles of polycarbonate plastic to each of the four corners to support the plate. That was all I had to do to modify this particular film holder to use for wet plate - it was very simple. Look for a film holder with a metal septum that can be pulled out with strong pliers.
    Tin Can

Similar Threads

  1. Plate sizes to standard sizes
    By Archphoto in forum Cameras & Camera Accessories
    Replies: 7
    Last Post: 23-Apr-2009, 14:06
  2. ERA Film in plate sizes
    By Martin Courtenay-Blake in forum Darkroom: Film, Processing & Printing
    Replies: 2
    Last Post: 13-Apr-2008, 13:46
  3. Plate Sizes
    By jantman in forum Cameras & Camera Accessories
    Replies: 13
    Last Post: 7-Sep-2005, 08:28

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •