Search:

Type: Posts; User: LabRat; Keyword(s):

Page 1 of 53 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    3
    Views
    98

    Re: Advise for Macro Lighting with Strobe

    First, modeling lights are unreliable for metering and strobe brightness estimations, as the lamps output vary over time/use, so you should be reading the flash exposure directly... A 1deg flash spot...
  2. Replies
    41
    Views
    1,164

    Re: Hole Saw For Commercial Ektar Lens

    The hole saws transfer a lot of torque to the workpiece as the entire diameter has teeth that are cutting/grabbing during operation and potentially distorting board... And the clamping has to be very...
  3. Re: How to remove heavy casing from 24" Aero Tessar

    I ended up with one of these 10 years ago for about $5... I had gotten the lens cells out without too many problems, as I loosened the set screws, but 1 cell was a little stuck... I put a rubber...
  4. Re: How to remove heavy casing from 24" Aero Tessar

    There is a couple of small set screws holding cells from rotating, so remove them first...

    Steve K
  5. Replies
    41
    Views
    1,164

    Re: Hole Saw For Commercial Ektar Lens

    For metal, boring bar on a mill...

    For wood, I use a circle cutting attachment on my router... Beautiful hole...

    On some retaining rings, there is a shoulder that can go inside the board that...
  6. Replies
    13
    Views
    230

    Re: Flash Cable for Kodak Supermatic Shutter

    For a long time I used an AC cord for an electric razor... Worked great!!!

    But as mentioned, Paramount will make you a bi-post to AC connector sync cord...

    Steve K
  7. Re: Chamonix and Ebony's are gorgeous & Old Kodak 2D's are UGLY but they have their p

    What would you rather wear on a daily basis??? A tux or expensive suit that looks great, or old comfortable clothes you don't mind getting a little dirty if you have to and you can get away with...
  8. Replies
    15
    Views
    731

    Re: where to look for used gear

    Suggesting to those starting out to just get something basic to start shooting with (to get the hang of it), then allow time to find items as they slowly start showing up (could even take years)......
  9. Re: LED enlarger head creation -- just a thought

    Not super easy to replace on a Beseler or Omega due to the fact that both were basically designed for condenser stages that integrated into the upper body of the head... The add on heads usually had...
  10. Replies
    9
    Views
    388

    Re: Time to get Serious about DIY

    Film will go the route of the LP...

    Remember the reports of the LP's demise???

    Though if x-ray units go totally digital, there might be less coating lines out there that make photo film on the...
  11. Replies
    17
    Views
    538

    Re: Changing bags and dust

    A shop vac with a drywall dust bag and brush attachment works well for cameras, holders, changing bags, cases etc... Bag the things you clean ASAP, and don’t put anything down someplace that harbors...
  12. Re: Mailing exposed 4x5 film to lab for developing

    Let it sit for a week or so if you are worried... It dies, usually sooner...

    Steve K
  13. Re: how to remove the nameplate locking ring from a Graphex/Rapax shutter No. 2?

    Inner, under the lens mount... Careful, as to outer dial will want to come off easily...

    Steve K
  14. Re: how to remove the nameplate locking ring from a Graphex/Rapax shutter No. 2?

    The ring is not on too tight, as that would bind the speed dial... Usually will come off using two opposing fingernails pushing counterclockwise...

    Don't loose the thicker high speed spring that...
  15. Re: LED enlarger head creation -- just a thought

    Well, the easiest conversion for the everyman (or woman) , (for B/W) is using the condenser is simply changing out the bulb for a bright (slightly)warm white LED + diffuser at the same height of the...
  16. Re: Mailing exposed 4x5 film to lab for developing

    Film boxes... Leaves no question for the lab on how to handle it...

    Ask the lab if they have some they can send you (they usually have them)... And ask the lab if there is any other way they...
  17. Replies
    28
    Views
    966

    Re: Why are all of my photos soft?

    One older Epson scanner we had developed problems focusing, so that might be an issue...

    Steve K
  18. Replies
    4
    Views
    209

    Re: Waterhouse slot for 8 3/4 inch Verito

    Actually, I read that here some years ago, and some combination worked when I "borrowed" the Betax #4 from a TR 15" I had, but strangely enough, the Studio shutter on my Verito works well, but...
  19. Replies
    15
    Views
    494

    Re: Hollywood Lighting

    They would make them look up so that shadow didn't become a mustache and stretch the muscles and skin... Must have been tiring to the subjects eyes!!!

    Steve K
  20. Replies
    4
    Views
    209

    Re: Waterhouse slot for 8 3/4 inch Verito

    The other option is these will fit stardard Betax shutters with their extension barrels on the elements (or at least mine with the studio shutter fit a Betax #4), but you have to check... And then...
  21. Replies
    10
    Views
    428

    Re: Tape like a post it note

    At better home and hardware stores, there is another 3M tape that is made for sensitive or delicate surfaces... (Like masking over existing house paint...) I forgot the name, but it is thicker but a...
  22. Thread: Spot meter

    by LabRat
    Replies
    24
    Views
    855

    Re: Spot meter

    Then there is the basic test... Bring both outside on a sunny day, meter a grey card with both, one should read close to the "sunny 16" rule, which is in normal bright sunlight, at f16 set, the...
  23. Replies
    6
    Views
    250

    Re: Practical Movements for 90mm 4x5

    Like Bob sez, and also note that you will have to choose your lens first, as some lenses fit inside the shutter, and some reach far back, and this difference can affect the tilt/swing angles...
    ...
  24. Re: Artcraft still taking orders these days ( its the Cusp of Spring 2020 )

    John, and you stay away from me too!!! ;-)

    Steve K
  25. Replies
    14
    Views
    478

    Re: Out of Stop, switch to water?

    When I started using Foma 100 (and my remaining stock of Efke 25), I would occasionally get pinholes on these films when using acid stop bath... I actually then read the instructions and they said...
  26. Re: Artcraft still taking orders these days ( its the Cusp of Spring 2020 )

    Hey John!!!

    I placed an order a month or two ago, and it took about a week for him to get back to me, so there was a slight lag... Try emailing AND calling first, then wait, before assuming the...
  27. Replies
    19
    Views
    593

    Re: omega D2 4x5 to 5x7 ???

    Possible to build enlarger head chassis with new machined parts, but a lot of design and machining, longer bellows, neg carriers, but would still need an entirely new light head...

    Might be easier...
  28. Thread: Filter fog?

    by LabRat
    Replies
    8
    Views
    375

    Re: Filter fog?

    Moisture, that dries up... Changes of air pressure slowly force moist air over time that cannot leave... It dries over internal surfaces, ultimately leave a haze...

    Ammonia based lens cleaners...
  29. Replies
    28
    Views
    883

    Re: Better lens for my Crown Graphic?

    So, have you actually shot this lens yet, and did you find the results unacceptable???

    One of the pros I worked with used the top lenses for studio 4x5's, but wanted a Graphic for field personal...
  30. Re: Compur Shutter and Strobe firing at slow shutter speeds

    Clean the contacts first... If there is a imperfect connection when internal contacts are closed, they can miss or multiple fire... Most old plated contacts will be oxidized...

    Steve K
  31. Re: Picture frame refurbishing a la cheap with polyurethane

    If you switch to shellac, there is a brief out gassing period that alcohol leaves, but then inert...

    Steve K
  32. Re: Photographing long hallways - tilt or swing to achieve maximum focus?

    You can get one wall in great focus by using swings, but at the expense of other planes further OOF...

    Think of your focus plane like a wedge shape... The narrow apex is closer to the camera, and...
  33. Re: Photographing long hallways - tilt or swing to achieve maximum focus?

    First, make a chart of hyper focal distances for each lens for different stops to use, and maybe a focus scale on the bed of the camera to dial in focus, rather than view it (my old Linhof Tek III...
  34. Thread: DIY Filmholders

    by LabRat
    Replies
    36
    Views
    8,815

    Re: DIY Filmholders

    I have tried to replace some light traps on old holders, and noticed some stuff...

    The Velcro idea seemed good at first, but in practice turned out that some tiny pinholes of light can go through...
  35. Replies
    25
    Views
    1,968

    Re: I can't get my 4x5 back from the repair guy

    I have had amazing results these days after I mentioned to the business owners in question that I will be sure to write up a detailed online review about my experience working with the business......
  36. Replies
    14
    Views
    774

    Re: New Dektol Mixes Dark Brown

    But can stain trays and paper base...

    Steve K
  37. Re: What happened when I mixed ID-11 (calling on ID-11 users)

    Most off the shelf MQ developers will mix with some color due to some oxidation... A pinch of sodium sulfite in the dilution or mixing water reduces it by getting rid of free oxygen in the...
  38. Replies
    31
    Views
    1,510

    Re: Best enlarger you have used

    One that holds consistent fine alignment, and is user friendly in use...

    Steve K
  39. Replies
    8
    Views
    382

    Re: VCCE vs Color Head (for B&W)

    The main difference is callibation for the specific materials and the B/W head does not have a cyan filter...

    MG settings on a color head are not too hard to get the hang of if you have an old set...
  40. Re: Advice on a spare-time project? 4x4 back and holders

    That got into my head also, but I wanted to get up a little closer to subjects where it becomes less of an scene, but more of the zone where the image becomes much more form oriented... And I was...
Results 1 to 40 of 2119
Page 1 of 53 1 2 3 4