Search:

Very cool. That's two Ubers, the red standards, and the magnifier. Uberuber, Superuber, Uberzwilling?
Again Very Cool!

Well, I'm not trying to be political at all. The state I live in removed all mask mandates, indoor dining, everything a month ago. We have the UK variant going exponentially. We are close to last...

I picked up a spare Metrolux II just in case. I used Beseler dichro heads for 20 years for color and black and white. Mixed magenta and yellow at close to constant neutral density. I bought a cold...

I don't support myself with MY work. My wife however is an artist, she's had shows canceled, she still has sales. It's kind of a catch 22. She's trying to be ready for her exhibition, so she's...

Metrolux II integrating timer. 2 channels, works with any light source, requires a photo cell, I have Zone VI VC heads with factory cells. Closed loop system.

I've used a Gralab 451 and 450. For...

That's good news.

The stand I have had been monkeyed with the table and the cranks were reversed, thus the table was on upside down. I confirmed this as Deardorff used L and R part numbers on the parts. It should be...

To Tin Can's point about the lead weights, if you stand it up make sure the lead weights don't slide, you can break the cast aluminum attachment points, then as has been said you will be glum.

Throw it away before you get in too deep!!

OK I have no idea, maybe for switching RGB filters for additive filtration for color???

Simmons had a cool dual filter system for Varigam VC papers,...

I think I have noticed more wisdom here. There's a lot of experience, in professional work. Something I've never tried to tackle. I've dabbled with darkroom, film, cameras for over 50 years. I still...

There's only so many different tubes. Some are labeled differently. The 2870 is what you add to a 2830 to get a 16 x 20 tube. Or in theory 4 8x10s. If you take the same 2870 tube, this is NOT LABELED...

Oh, yeah the original bad XTOL which the bag I got worked. I got a replacement, now the replacement is on the troubles list, so I'm supposed to be getting that replaced.

Pretty amazing. All I've ever used for film has been Kodak chemistry, since I was a kid, my Dad and I developing Instamatic Verichrome in Microdol-X. I've never been hurt by Kodak's chemistry, but...

I just checked, all of the Ilford powdered b&w chemistry, listed at Freestyle are out of stock. I suspect that the cargo and delivery services being overwhelmed is the cause. I got a reply from...

Freestyle sells Eco Pro same thing as XTOL, schools use it lower prife. Foma makes a 1 liter pack, not sure what it is. Now that Sino Promise has full control of the chemical and paper division I...

Try finding some of the Ilford products. It's crazy, I am addicted to Bromophen, I found 2 boxes available at Adorama, no ETA on anymore, there's no Microphen. It's hit and miss. I suspect some of...

Good for you! I may try this sometime, I want RGB for color, not sure I have the brains for it.

Same thing with Ilford Bromophen 5L, store pick up only. It may be that they are short on stock. Ilford in UK shows several chemistry items out of stock. Microphen, DD, Bromophen, and several other...

Yes, the Panasonic bathroom vent fans are amazing, quiet! My blower system is rarely used. I can tone with selenium without a problem. I use citric acid stop and rapid fix. Film development color...

Hey cool 3D printing

I have never liked forced air drying for films. I would just use distilled water and 1 drop of LFN or PhotoFlo. Too late to say more now. Keep the air exchange to a minimum. Humidity control is...

The first rule is if you want air going out, you need temperature and humidity controlled air coming in. I was gifted a Doran setup like you have it helps but if you are using sulfide toner, or...

Truth!

I've been using Kodak Flexicolor for a while. I remember some E6 kits had crystal dry chemical for the final rinse. I found a few tiny white crystals on the dried film. Brushed them off with a camel...

My tap water is loaded with minerals. I installed a reverse osmosis system. Makes, almost, as pure water as distilled. I use the RO water, for final rinse, powdered developer etc. Purified water at...

Make a contact print, then scan that.

Not sure what C-41 process you are using. Tetenal, Kodak??

With Kodak processes, after fixing you need to wash film for 2 minutes, then treat with Flexicolor Final rinse, prepared with...

I've had a Crown Graphic for 30 years. It's a great camera for handheld rangefinder focused pictures. Tmax 400 f16 500th in the sun. Original Xenar 135mm (is it Xenar?) It's the little 4 element...

I thought the bed drop was so you don't see it when using a 65mm wide lens? ??

You are correct about treating water. We have so much Calcium carbonate dissolved in our water we use a water softener, it does a great job. The ion exchange resin exchanges sodium for calcium. The...

Money :o

Go to Ebay and buy an old Kodak Color Darkroom Dataguide, it's got formulas for adjusting times based on several factors, filters etc.

1 135-36 equals 1 8x10 sheet equals 1 120 film. 4 4x5 equal 1 135-36

Everything that has been said is good advice. I would use your Jobo. Maybe get a couple 2830 tubes. I still use ancient Kodak drum processors, I run at 100F/38C. You are using a dichro colorhead, so...

They are probably ok if stored dry and cool. I've used some old XTOL with no problems. I've always kept in humidity controlled cool space in sealed plastic bins. If the powder flows freely and the...

A friend of mine who recently closed his shop, he retired. They used a 850 for anything bigger than a 6x7 cm negative. He was very satisfied, no wet mounting.

Pull off the front and rear lens groups, open the aperture wide open, lock the shutter open. If it's really just paint, you could apply a gel paint remover with a Q tip. Buy a lens spanner. I have a...

Good advice on all counts. I was beating on a center punch with a 20 oz ball peen hammer the other day. The punch went boing, still haven't found it, had my face shield on. Shouldn't have to remind...

The "cylinders" are not round. They are two injection molded halves that are solvent welded together by Jobo. Do you have a "crack" very unlikely unless the cylinder was struck with considerable...

The tanks are ABS, so as mentioned something made for a Styrenic model kit could solvent weld the crack if you could get to it. Sounds like what you have is working. Once you have Silicone on the...