Fuji HR-U X-Ray Film Developer Test: 510 Pyro, Rodinal, PaRodinal, D-23

Now that I have my 8x10 gas burst system working, I decided to see which developers work the best with it and Fuji HR-U x-ray film.

I think I still like 510 Pyro the best but the others I tested have their strong points.

510 Pyro

510 Pyro delivered the most middle-ground negative. It is contrasty but not overly so. The grain is sharp but not too sharp. It stains the negative, which I appreciate for my alternative process printing, and it tans the very delicate x-ray film. It is also one of the cheapest at $1.44/gallon at 1:100 dilution and has a fast development time of 6 minutes.

On the bad side, it was the most finicky. It required the most perfect agitation (I built a gas burst system) and modifications to my 8x10 hangers to avoid surge marks. At dilutions dilutions over 1:100 I saw both bromide drag and surge marks at the same time (too much and not enough agitation concurrently).

510 Pyro Negative (yellow stain):
Attachment 223865

510 Pyro Scan:
Attachment 223866

Face Detail:
Attachment 223867

Grain Detail:
Attachment 223870

R09 One Shot Rodinal

R09 Rodinal delivered a contrasty and noticeably sharper (higher acutance) negative than 510 Pyro. Dense (white) background areas were smoother and it masked uneven agitation exceptionally well. Shadows from the hangers were virtually eliminated. It is similarly economical to 510 Pyro at $1.44 per gallon at 1:100 dilution.

Negatives: I got pepper-like black specs covering denser areas. These were persistent across multiple tests and I don't know what caused them. This was a deal breaker for me, though if you're only doing contact prints you might not care. These negatives also have less shadow detail than the other developers and I felt like they were a little too sharp for portraits done with modern lenses.

Here are the black spots:
Attachment 223871

510 Pyro (left) vs. Rodinal (right):
Attachment 223873

Rodinal Scan:
Attachment 223874

Face detail:
Attachment 223875

PaRodinal (Tylenol developer)

After seeing the smooth dense areas that Rodinal delivered, I decided to try making it. PaRodinal isn't Rodinal but it has the same developer (p-aminophenol). You make it by grinding up Tylenol tablets, adding drain cleaner and a bit of sodium sulfite and waiting a few days. The sodium hydroxide synthesizes the tylenol into p-aminophenol. Cost is an impressive $0.17/gal at 1:100.

https://www.thorleyphotographics.com/?page_id=271
https://www.brodie-tyrrell.org/wiki/index.php?Parodinal

The negatives I got from PaRodinal are nearly indistinguishable from rodinal, but without the black spots.

Downside: in addition to the thin shadows and overly sharp faces, this developer dies fast and hard after only about 6 minutes in my (air) gas burst system. It has very little sodium sulfite preservative in it, and possibly the sulfite precipitates out of the solution (I have read conflicting reports of what the precipitate is). The instructions for use mention scooping some of it into your dilution, but this obviously not going to get you consistent results. I did a second test where I didn't scoop any out but instead added fresh sodium sulfite to the developer bath in the amount that would be present had it not precipitated out. This improved developer life and the negatives continued to add density until at least 7 minutes (the end of my test).

This was a fun project and would be appealing for ULF where you need multiple gallons of developer but I think it's a little too funky for my use.

Rodinal (left); PaRodinal (right):
Attachment 223877

PaRodinal scan:
Attachment 223876

PaRodinal face detail (sharp!):
Attachment 223878

Grain detail (no pepper):
Attachment 223879

D-23

D-23 produced dramatically softer negatives than the other developers tested and it was the most well behaved. Shadow detail was dramatically better than the other three. However, I can't say I like the character of the grain and softness of the detail.

I used D-23 at 1:3 dilution. 8 minutes was a bit thin, 10 minutes was a bit dense, so I think 9 min would be good for HR-U. It was the most expensive at about $2.20/gal.

Maybe a reduced sodium sulfite version would be better -- less expensive and sharper?

PaRodinal (left); D-23 @ 10 min (right). The D-23 is has much lower contrast and better shadow detail:
Attachment 223885

D-23 Scan (much more detail in black jacket and pants):
Attachment 223884

Face detail (mushy soft):
Attachment 223886

Grain detail:
Attachment 223887

Thanks.

I have Rodinal (original) at hand so I'll pour that onto the two 8x10 shots I want to develop and see where it gets me.
Usually I have the 1:100 dilution for 60min stand development but I think I'll cut it short at 30mins.

EDIT: turns out the Massive Development App also has the Fuji HR-U film listed and says 4:30mins in Rodinal 1:100. I did 5:30 and sheets came out properly developed. Sharpness etc not so much but I'll scan them after all tomorrow.

If I get anything worthwhile I'll post back here.


This thread was the first info I saw in search results. Once we had Search Engines, today we have Serve Engines... buy buy buy is all they offer... yuk.

I use Rodinal for years

1/100 most of my time

or Ilford PQ for ancient plates and films by inspection

Rodinol dies after 20 minutes

Quote:

---

Originally Posted by buzzardkid

Thanks.

I have Rodinal (original) at hand so I'll pour that onto the two 8x10 shots I want to develop and see where it gets me.
Usually I have the 1:100 dilution for 60min stand development but I think I'll cut it short at 30mins.

EDIT: turns out the Massive Development App also has the Fuji HR-U film listed and says 4:30mins in Rodinal 1:100. I did 5:30 and sheets came out properly developed. Sharpness etc not so much but I'll scan them after all tomorrow.

If I get anything worthwhile I'll post back here.


This thread was the first info I saw in search results. Once we had Search Engines, today we have Serve Engines... buy buy buy is all they offer... yuk.

---

There's a thread with about 20,000 entries in it in this category of this forum. I guess you missed that. Web searches will turn up results in this forum pretty regularly. HR-U processes like most black and white films, but requires a gentle touch due to the two emulsion surfaces that are easily scratched in processing.

It would be helpful to know with test results:

1. Format
2. Light source used.
3. Film speed used for exposure.

Alan Townsend