Possible LED light source for enlargers
Just received an e-mail promotion from Rosco for their new LED lights.
http://www.rosco.com/lighting/litepa...eturn=lighting
The "LitePad" DL and HO+ daylight units look like they could make a good enlarging light source, especially the 12X12 size for an 8X10 enlarger.
I have a Beseler 8X10 with a 12X12 Aristo cold light head and I will measure the output in FC at 12" and compare to the specs on the Rosco 12X12 LitePad.
It is only 8mm thick. If one were made to carry a negative with a hinged ANR glass to the same size as an 8X10 or larger film holder, it could slide into the back of a view camera to make it an enlarger.
Re: Possible LED light source for enlargers
I have had little respect for 8x10 LED light sources as being too dim, however, after seeing this years Le Mans race (LED headlights on the cars) I'm expecting something like this.
I think I can actually compare the stated output to my 2000W Durst CLS2000. The specs on the 12x12 unit indicate an output of 3200 LUX at 6". That would be close to EV10 with ISO 100 film. I suspect it would not be too much trouble to reach my incident meter through the 8" lens opening and measure the output of the Durst mixing box about 6" away.
Re: Possible LED light source for enlargers
The answer is....LED still not as bright, but probably bright enough for many applications. I suspect the technology will continue to progress.
CLS2000 at 6" = EV14 = 40,960 LUX
ROSCO 12x12 LED panel at 6" = EV10 = 3200 LUX
Re: Possible LED light source for enlargers
Would this be usable with VC papers? Do white LEDs have enough of the spectrum to enable the use of traditional VC filters?
Re: Possible LED light source for enlargers
NO. I doubt they'd be suitable. I've used the original lite pads extensively for motion picture work and they aren't that bright. Now the Tungsten Lite Panel 1x1 (litepanels.com) would be closer.
Quote:
Originally Posted by
Neal Chaves
Just received an e-mail promotion from Rosco for their new LED lights.
http://www.rosco.com/lighting/litepa...eturn=lighting
The "LitePad" DL and HO+ daylight units look like they could make a good enlarging light source, especially the 12X12 size for an 8X10 enlarger.
I have a Beseler 8X10 with a 12X12 Aristo cold light head and I will measure the output in FC at 12" and compare to the specs on the Rosco 12X12 LitePad.
It is only 8mm thick. If one were made to carry a negative with a hinged ANR glass to the same size as an 8X10 or larger film holder, it could slide into the back of a view camera to make it an enlarger.
Paul,
they do require color correction when used for motion picture work because there is a bit of a green spike.
Re: Possible LED light source for enlargers
Quote:
Originally Posted by
Paul Ewins
Would this be usable with VC papers? Do white LEDs have enough of the spectrum to enable the use of traditional VC filters?
I assume filters in front of white LED's will change the grade in the desired direction, but probably in quite different steps than the filter number suggests, so a recalibration of the grades would be necessary. The VC filters are made for continuous spectrum incandescent light sources, and white LED's are a pretty far cry from that. Most of them just use a blue LED plus a phosphor that absorbs part of the blue and then emits in the yellow(ish) spectrum. The CRI of most white LED's is therefore well below 90.
That being said, if you have one of those panels, experimenting doesn't hurt.
Re: Possible LED light source for enlargers
Quote:
Originally Posted by
ic-racer
The answer is....LED still not as bright, but probably bright enough for many applications. I suspect the technology will continue to progress.
It is progressing. The company I work for specialises in placing LEDs (and other components) on flexible polyester circuits. We do work for this company: http://designledproducts.com/ on various lighting products, some of which are shown on their website.
LEDs will soon be a viable replacement for fluorescent (and tungsten) lighting. In fact, it is already. We are soon going to have all of our office lighting replaced with LED panels.
Quote:
Originally Posted by
Arne Croell
I assume filters in front of white LED's will change the grade in the desired direction
I'm not sure. I have red, green and blue LEDs in my enlarger and change contrast by varying the green and blue LEDs. I am going to try white soon though.
Steve.
Re: Possible LED light source for enlargers
Quote:
Originally Posted by
Steve Smith
I'm not sure. I have red, green and blue LEDs in my enlarger and change contrast by varying the green and blue LEDs. I am going to try white soon though.
Steve.
I use blue -green LED's too (I have both the Calumet and the Heiland LED heads) and they work fine. No reason to change that. What I meant with "in the right direction" is, that if you use a yellow filter in front of a white LED panel, you will get a softer grade, and a harder one for the magenta filters - there will be some effect. How big that change is, whether it is close to what the filter no. implies, and if it is possible to reach really soft or really hard grades, is a totally different story and has to be tried.
Re: Possible LED light source for enlargers
I think you are right, you will push it towards harder or softer grades but I don't think you will get near to grade 0 or 4. I think my blue and green LEDs give me about 1.5 to 3.5 at most. I wouldn't expect even that range with filtered white LEDs but I wouldn't mind being proved wrong!
Steve.
1 Attachment(s)
Re: Possible LED light source for enlargers
I noticed the parking garage where I park changed over totally to LED lighting. Something like these 16"x16" (external dimension) units. That looks more like something to sit on top of an 8x10 enlarger: http://www.lsi-industries.com/docume...-datasheet.pdf
Attachment 77431
Since the price on these is secret, so they can scam institutional clients I suspect, I wouldn't be surprised if it cost more than a second-hand Durst CLS2000 head.