I just developed a sheet and I noticed a dark strip on the right side of the image (see attached). I'm not sure what that could be (I used the sp45 development tank).
Attachment 191888
Printable View
I just developed a sheet and I noticed a dark strip on the right side of the image (see attached). I'm not sure what that could be (I used the sp45 development tank).
Attachment 191888
This is the single most common mistake in film processing here or on other sites I see.. Problem is neutral sky's or grey areas show process defaults.. To solve this the first 15 seconds of development good agitation must happen, as well sufficient chems to process in.
I use Jobo system and even then I will invert and twist for 15- 20 seconds to ensure chem's get to all areas of the negatives and fast. hope you solve the problem .
Because you didn't cover the entire film with developer at the same time. For example, you were tray processing and put the film into the developer emulsion side up and didn't get that last bit on the right side pushed under the developer for a second or two (and that's all it takes) after the center was pushed under.
Film development is weird stuff -- the first couple of seconds are crucial to getting even development.
I always use a pre-wash to guard against this problem. Some film makers say a pre-wash is not needed. However, with a few film and developer combinations it is absolutely necessary.
I have not solved photography and don't know the answer to your question; however your problem interested me enough to watch a tutorial video about the SP-445 tank, so I have some idea of how the tank is constructed and how it is supposed to work, and on the basis of that very limited bit of information, I offer the following for your consideration. First of all, it is clear that this aberration is caused by uneven development, i.e., namely that the edge received less development than other parts of the negative and therefore the positive is darker in the affected areas. Second, and very importantly, the problem is not limited to the right side of the image. If you look very carefully at your scan you will see that the problem occurs on the left side as well. It is not so obvious along the full length of the image, but it is apparent in the lower left corner of the positive (the difference can be made more obvious by running the image through different filters in PhotoShop and, I assume, other comparable programs). So taken together, what does all of this suggest? My guess, and here I cannot overemphasize the word "guess," is that you may have inadvertently loaded the negative in the an orientation opposite to that recommended by the maker, i.e., the film was loaded with the emulsion side facing the continuous, unbroken, flat part of the holder vs. having the emulsion side facing outward toward the intermittently-spaced tabs that hold the sheet film in place to prevent it floating away from the holder. If that is indeed what happened, then it may be possible that the developer did not reach those edges of the film as quickly as the developer covered the remainder of the negative, e.g., because the film edges may have adhered slightly to the flat parts of the holder, partially on the positive left, and more completely on the positive right, for a brief time - certainly longer than 1 or 2 seconds - and the agitation provided was not sufficient to dislodge the stuck parts quickly enough to give even development across the entire negative. I do not know the proper name for this adhesion but what I am thinking of is not unlike what happens when a bit of liquid or humidity causes a dry negative to stick to another negative, to a polyethylene sleeve, or to some other material. I assume the problem could be exacerbated if you happened to use only one holder and cross loaded it so that there was more pressure on the edges than would otherwise occur, but I am certainly not suggesting that was the case. I do not assert that this theory is correct, and will not be the least bit embarrassed or ashamed if it is determined to be wrong. In the meantime, I too recommend that you pre-soak to minimize this problem going forward if you are not already using a pre-soak, and I also recommend that you contact the manufacturer of the SP-445 directly to see what they might have to say about the cause and cure, especially if the problem is a recurrent one.
N. Riley
http://normanrileyphotography.com
N. Riley's idea is highly probable, and you can check for yourself. Measure the width of the plastic bars on each side of the holder. If they correspond, that's your answer. Early on with this tank, I managed to load two sheets in the same side! It happens.
Another suggestion for future: Tim, the creator and seller of the SP-445, is quite responsive on email. He helped me figure a few things out over email.
I developed another negative with the mod54 and got the same result. I think it might be the bellows that is shading a bit.