View Full Version : b/w paper processing in Jobo drums?

David Haardt
22-Jun-2001, 13:44
Hello folks,

I wondered whether one can process b/w paper in Jobo drums. There is a Jobo drum which can accomodate papers up to 50x60cm (20x24") so that would be rather nice . You only need 300ml of chemicals. But the Jobo web site says that this tank is only for processors, and for colour prints. So my two questions: Can I use it f or b/w prints too? (Are there any disadvantages?) Can I use it by rolling it on my desk too, or do I really need a processor? (The Jobo web site says that the s maller drums can be used manually too, but this large one not.)

Best regards,

Pete Caluori
22-Jun-2001, 17:09

You can see some similar posts on using FB paper in JOBO drums, by scrolling down a bit. To answer your question specifically, You can probably get away with it, but there are some pitfalls to be aware of:

Using the drum off the processor means that the chemistry wont be distributed evenly at first and may result in streaking. If you use a long development time this shouldn't be an issue. You probably wont have complete fixing if you use a short rapid fixer. Rotation should be bidirectional.

The ribs inside the drum will cause ripples in the paper, which will come out with sufficient washing and flatening. These ribs may cause a large sheet of paper to free float inside the drum resulting in a wasted exposure.

When using a minimal amount of chemistry in a drum that size, the drum must be perfectly level while it's rotating, or parts of the print will not be fully developed/fixed.

FB papers get very limp when wet, whereas color or RC papers remain stiff; this is the reason JOBO doesn't recommend FB prints in these drums. I have the drum and use it for color & RC prints; I tried it with FB 8x10's and the paper tends to free floats inside the drum once it gets wet, but that was with 6 sheets of 8x10. One large sheet might work, but you'd probably be better off with trays.


David Haardt
22-Jun-2001, 17:41
I am particularly interested in the Jobo drum 3063, because on the Jobo web site it says that most of the smaller tanks can be used manually, but this one is for processors only, and I wanted to know whether this is based upon facts or not. It would also be interesting how the interior of the drum is made to know which problems could occur.

Best regards,

Pete Caluori
22-Jun-2001, 20:42
Hi David,

This drum is one piece (not including the lid) and as you can imagine, quite large. The lid contains a small light baffle, but does not "hold" chemistry. The lids on 2xxx series drums not only contain a light baffle, but they will hold chemistry. In use, chemistry is poured into the lid (2xxx series drums.) Only after the tank is brought to a horizontal position will chemistry contact the paper. In the lid of the 3xxx series drums, there is no capability to "hold" chemistry; as soon as it's poured in, it will hit the baffle and will splash around inside the drum. This is the reason JOBO does not recommend these drums be used off the processor - uneven development could occur.

Please beware, I have not tried this, but it does sound reasonable. If you poured the chemistry in "quickly" and began rotating the tank "quickly" and developed for a sufficiently long time (I would think about 3 minutes) then you might be successful with B&W paper, but don't ever try this with color paper/chemistry. Similarly, you would have to fix the paper for a sufficiently long time. I would not try the Ilford 2-bath 60 second fix with this arrangement. You would also need to insure that the drum rotates on a level plane to ensure even chemical distribution over the surface of the paper. When used on a JOBO processor, the drum is spinning while the chemistry is poured in.


scott jones
23-Jun-2001, 22:55
Hi David,

Please see at least three previous posts by myself re FB paper for black and white in the JOBO CPP-2. Single sheets seem to work fine for me thus far (8x10. I will be testing 11x14 soon and posting the results. It is best to use the processor I believe after experiencing all of this. Email if any questions...


Dick Silven
26-Jun-2001, 18:35
David, I have been using a Jobo #2850 for all my B&W printing for six years with no trouble. I use Ilford MGIV FB in all sizes from 5x7 to 16x20, processing multiple 5x7, 8x10 and 11x14 prints simultaneously with repeatable results and no difficulty. The ribs on the inside are the result of clever design - they are spaced so all popular sizes of paper fit snugly between a pair of ribs, preventing the print's floating. I can think of no disadvantages, and the work is done in the light with very small quantities of chemicals. Can't comment on hand rolling, but why would there be a problem if you start with a water rinse as recommended? Regards, Dick