Have you mounted a Nikkor-M 450/9 on a Linhof Technika lens board? How....?

[pepeguitarra]

I am having a lot of trouble mounting a Nikkor-M 450/9 on a Linhof/Technica/Lelund lens board. There is no room for a spacer, so the aperture controls fall right below the slide that retains the lens board. I wanted to avoid the large Sinar lens board when using it on my 8x10. Any advice?

[Lachlan 717]

Standard Copal 3 fitting.

Mine fits fine

[pepeguitarra]

Standard Copal 3 fitting.

Mine fits fine
THANKS, for sure, Copal 3, I have already tried two of them. The opening is not the problem. The problem is when I try to place the lens holder on the front standard of the Intrepid 4x5, Chamonix 45F2, or even the Korona View. The controls are too close to the lens and the standards are so small that it is impossible to access the levers. I have it mounted on a Sinar type board with a Copal 3, which is fine. But I want to have in in a small lens board (Linhof Tecknica) type. I have lens board reduction from 8x10 to 4x5, so I can use my lenses in 4x5 or 4x8. This one, I have to use it only on the 8x10 because of the fit.

[Bob Salomon]

THANKS, for sure, Copal 3, I have already tried two of them. The opening is not the problem. The problem is when I try to place the lens holder on the front standard of the Intrepid 4x5, Chamonix 45F2, or even the Korona View. The controls are too close to the lens and the standards are so small that it is impossible to access the levers. I have it mounted on a Sinar type board with a Copal 3, which is fine. But I want to have in in a small lens board (Linhof Tecknica) type. I have lens board reduction from 8x10 to 4x5, so I can use my lenses in 4x5 or 4x8. This one, I have to use it only on the 8x10 because of the fit.

Did the lens & shutter come with the spacer ring? If not you need one to ovoid the aperture control from rubbing against the board. Contact a camera repairman, or woman, to get one. It is normally supplied with new lenses in Copal 3.

[B.S.Kumar]

Wista and Toyo both made special top hat boards with threads for the shutter. They cost a bit more than usual. Extension boards are also available on eBay.

Kumar

[Bob Salomon]

Wista and Toyo both made special top hat boards with threads for the shutter. They cost a bit more than usual. Extension boards are also available on eBay.

Kumar

He needs the spacer ring, not a top hat or extension board.

[pepeguitarra]

Thank you Bob. I do have the spacer and the ring. I just realized that I was using a Linhof/Technica type lens board that has TOYO cast in the back. The Copal 3 opening only allows the screw of the shutter to go through. I got one of those Luland (recently reviewed in this Forum), and the opening Copal 3 is a bit larger, allowing for the ring to go through. I just placed the spacer and the ring and the lens is working fine. Thank you Lachlan and Bob for the help. I just learned that not all the lens board Copals are created equal.

[Lachlan 717]

Excellent outcome!

[B.S.Kumar]

Thank you Bob. I do have the spacer and the ring. I just realized that I was using a Linhof/Technica type lens board that has TOYO cast in the back. The Copal 3 opening only allows the screw of the shutter to go through. I got one of those Luland (recently reviewed in this Forum), and the opening Copal 3 is a bit larger, allowing for the ring to go through. I just placed the spacer and the ring and the lens is working fine. Thank you Lachlan and Bob for the help. I just learned that not all the lens board Copals are created equal.

I believe your Toyo board may be for a Copal 3S shutter. The correct size hole for a particular lens/shutter allows the retaining ring to fit snugly. A board for a Copal 3S shutter would let the shutter pass through, but not the retaining ring.

Kumar

https://i.postimg.cc/65HjjvsT/Toyo-Copal-3-Lens-Board.jpg

[pepeguitarra]

Kumar: You are right, that is the lens board I have. Luckly, I order several from Lulund, at $13 /piece. Thanks for the info. Pepe

[pepeguitarra]

Here is the final result. Yo can see the Toyo (Copal 3S) that Kumar mentioned. Also, the larger lens board where the lens was earlier.
https://farm8.staticflickr.com/7845/47231615362_a73cfc035c.jpg (https://flic.kr/p/2eXGnHU)20190304_154933 (https://flic.kr/p/2eXGnHU) by Palenquero Photography (https://www.flickr.com/photos/palenquero/), on Flickr

[B.S.Kumar]

Is the gray board a Toyo? I cannot recollect a Toyo Copal 3 or 3S board with an offset hole. All the boards I have for Copal 3S and larger shutters have holes centered with respect to the raised lip.

Kumar

[pepeguitarra]

https://farm8.staticflickr.com/7810/47231942382_04750face3.jpg (https://flic.kr/p/2eXJ3Wb)20190304_164955 (https://flic.kr/p/2eXJ3Wb) by Palenquero Photography (https://www.flickr.com/photos/palenquero/), on Flickr

[B.S.Kumar]

Strange. Unless someone made the hole themselves.

Kumar

[pepeguitarra]

Not sure, I bought it from one of those Japan dealers on the bay.