View Full Version : 90 inch bellows - what is exposure?

FrancisF

12-Aug-2017, 14:54

I am setting up a shot I have tried before…unsuccessfully. Here are the specs. I am foggy on the bellow extension factor and reciprocity failure. The set up is for a head shot in the outdoors. It is about a 2X enlargement.

20 x 24 Ilford FP4 film (125 ASA)

About 90 inch bellows

About 50 inch subject to lens distance

24 inch Goerz Artar Red Dot lens apochromat (American Optical) (no shutter) at f11

Gossen Luna Pro meter reads 17 which indicates a speed of 1/1000 at f11

What exposure should I use?

Thanks,

Francis

blue4130

12-Aug-2017, 15:14

Are you using flash or daylight?

Tim Meisburger

12-Aug-2017, 15:20

Measure the opening in the lens (the aperture) on its widest f stop. Divide 90 inches by that measurement. Assume for a moment that the opening is one inch, then your actual f stop is f90. Use that to calculate exposure and you should be right on. So in your example, if the meter wants 1/1000 at f11, and you actually have f90, then you need to reduce your shutter speed to 125th of a second. Reciprocity is not relevant.

FrancisF

12-Aug-2017, 15:38

Daylight. in shaded area

Dan Fromm

12-Aug-2017, 15:51

Since you know the magnification, deciding what to do is easy. Effective f/# = (1 + magnification) * f/# set. At 1:1, effective aperture = 2 * aperture set. Set f/16, expose for f/32. At 2:1, set f/16, expose for f/45. And so on.

In your case, if the meter says 1/1000 @ f/11, you want a shutter speed three stops slower. 1/500, 1 stop slower; 1/250, 2 stops slower; 1/125, 3 stops slower. And there you are. Tim nailed it.

David Lobato

12-Aug-2017, 15:54

If the meter is reading an EV value of 17 at ISO 125, it's is too high for a shaded area. Shade would be close to 12 EV, 1/30th at f11 before bellows compensation. Adding 4 stops exposure for the 90 inch bellows is 1/2 second at f11. Someone correct me if I'm wrong on the 4 stops for the 90 inch bellows draw.

Dan Fromm

12-Aug-2017, 16:56

David, thanks for making me revisit the first post.

Francis, with a 24" lens 90" extension, 50" lens-to-subject distance (where did you measure from?) and 2x don't seem quite right. Would you please check your measurements?

2x wants 72" extension (rear node, which will be close to the diaphragm, to film distance) and 36" lens to subject distance (front node, which will be close to the diaphragm, to subject). This isn't your setup.

90" extension with a 24" lens means 2.75 x, lens to subject distance 33".

Jerry Bodine

12-Aug-2017, 18:30

FrancisF - I question your meter reading. I have a Gossen Lunasix and have confirmed that your meter reading of EV 17 does yield an exposure of 1/1000 @f11, but that level of luminance is nearly the highest that the meter can read and is far too high for an outdoor subject in shade. I suspect you're instead reading the Gossen SCALE (the one with yellow background) to be 17, thinking that's an EV value for ISO 125 (it is NOT), then turning the dial to an EV 17 setting to arrive at 1/1000 @ f11. If instead you set the dial at the 17 SCALE reading you would actually be at EV 12 (a realistic reading for such a subject). You would then be reading 1/40 @ f11; this result requires correction for bellows extension.

The formula for correction due to bellows extension with ANY lens focal length is:

Exposure FACTOR (i.e., a multiplier) = [extension/focal length]^2. The ^2 means the number in brackets is squared.

Using your info, given Extension=90 and FL=24, the resulting EF=14 actually amounts to 3.8 stops and can be rounded to 4 stops. Since the EF is a FACTOR used to increase your exposure time, the new exposure time becomes 1/40 times 14, or about 1/3 second; so 1/3s at f11. This is approaching the reciprocity region for most films, and since you don't have a shutter to control short exposures anyway you may want to close the aperture down another two stops (giving 1-1/3s) to lengthen the exposure time enough to allow you to use a flat black card/darkslide/hat in front of the lens to time the exposure by hand. Of course, you’ll be limited by how long the subject of your “head shot” can hold still during the longer exposure. Reciprocity would not be severe.

Jerry I agree 100% with your math (the bellows factor being 14), and with your advice regarding the actual exposure meter reading.

Rich

Johnny LaRue

12-Aug-2017, 19:20

Just a noob guess:

If your bellows is extended by almost 4x the lens' focal length, add 4 stops to the metered reading.

So f11 at 1/1000s becomes f11 at 1/60s.

Too easy? Too wrong? I'm missing something, right?

Luis-F-S

12-Aug-2017, 19:50

Funny thing, in open shade, I'd use 1 sec at f/22, by the time you stop 4 stops for the bellows and 2 stops to get you to optimum aperture!

Drew Bedo

13-Aug-2017, 06:01

So, lets see . . . .

The focal length of the lens is 24 inches.

The bellows extension is 90 inches.

Each focal length equivalent of bellows extension will require an additional two stops of exposure, either by opening up the lens or lengthening the exposure time.

So: 90 inches divided by 24 inches gives 3.75 focal lengths of extension.

With two stops of additional exposure required for each additional focal length of extension that is 7.5 stops.

(90/24)2=7.5

Do I have that right?

I don't know much about reciprocity issues, but this will be a long exposure.

Dan Fromm

13-Aug-2017, 08:50

A few useful magic formulas for closeup/macro:

These apply to symmetrical lenses. The OP’s Apo Artar is symmetrical.

f = lens’ focal length

m = magnification

Practically speaking the OP’s lens’ nodes are at its diaphragm.

Extension (distance from the lens’ rear node to film) = f*(m + 1)

Whence m = (extension/f) - 1

Distance from the lens’ front node to the subject = f*(m + 1)/m

Exposure adjustments:

Effective f/ number = f/ number set * (m + 1)

Exposure time increase factor = (m + 1)^2

If the OP tells his meter he is shooting at his lens’ effective aperture the meter will suggest the right exposure time.

Jerry Bodine

13-Aug-2017, 10:36

All good info, Dan. If someone's kit contains a lens that is known to be un-symmetrical it would be useful to know how the exposure correction is determined. For that I refer to an explanation published in my Leica Manual, excerpted here:

EF = (1 + m/mp)^2 where mp is the pupil magnification; mp is the ratio of the diameter of the exit pupil to the diameter of the entrance pupil (seen from in front of the lens). It can be determined with sufficient precision by looking first into the rear of the lens and then into the front. Obviously, mp=1 for a symmetrical lens but will be less than 1 for an un-symmetrical lens, thus causing a higher EF due to reduced illumination at the film plane. Many lenses for MF or 35mm are likely un-symmetrical designs, and if the camera has through-the-lens metering EF would automatically be accounted for; a rangefinder user would not have that benefit. So the EF for an LF lens that is not known to be symmetrical or un-symmetrical can be determined after measuring its mp.

So, lets see . . . .

The focal length of the lens is 24 inches.

The bellows extension is 90 inches.

Each focal length equivalent of bellows extension will require an additional two stops of exposure, either by opening up the lens or lengthening the exposure time.

So: 90 inches divided by 24 inches gives 3.75 focal lengths of extension.

With two stops of additional exposure required for each additional focal length of extension that is 7.5 stops.

(90/24)2=7.5

Do I have that right?

I don't know much about reciprocity issues, but this will be a long exposure.

No.

(90/24)^2 Means to square the quantity (90/24)

(90/24) = 3.75

3.75 squared = 14.06

That's the Bellows Factor. You have to increase the exposure 14 times. That's the equivalent of 3.8 stops exposure increase.

To get the number of stops from the bellows factor, either estimate in your head:

1 stop = 2x.

2 stops = 4x.

3 stops = 8x.

4 stops = 16x.

Since 14x is needed, it's a little less than 4 stops. You can safely round to 4 stops.

Or, the number of stops = Ln Bellows Factor/Ln 2.

You can also use Log base10. It doesn't matter.

Ln 14 = 2.6.

Ln 2 = 0.69

2.6/0.69 = 3.78 stops

Log base10 of 14 = 1.15

Log base10 of 2 = 0.3

1.15/0.3 = 3.8 stops

Rich

lungovw

13-Aug-2017, 14:28

My reasoning would be: f/11 with 24 inches focal length means an entrance pupil of 2.18 inches (24 / 11). Then I would measure the new lens/ground glass distance and calculate the actual diaphragm in this situation based on the entrance pupil that remained the same. If the 90 inches (bellows extension) is representative of that conjugated foci, then 90 / 2.18 = f/41.28, that I would round to 45 and get the same fours stops as Jerry and Johnny calculated above. I guess it is all the same. When distance doubles, area quadruples in the base of a cone light.

Tim Meisburger

13-Aug-2017, 19:15

There is a lot of unnecessary calculation going on in this thread. Just remember this formula: f number = focal length divided by internal lens diameter (more properly called entrance pupil). Lets call that F = fl/p. For most LF lenses you can simply measure the entrance pupil with a ruler and you will be pretty close, but it is also possible to calculate it if you have two of the three numbers, as lungovw has above. So

fl = 24, F=11, so p = 24/11 or 2.18.

Now the trick to all this is to remember that the fl stamped on the lens is its focal length at infinity. But in your case, you are not using the lens at infinity, you are using it at 90 inches, Consequently, your focal length for this image is 90 inches!

So, pop that in our equation (F = fl/p) and it becomes F = 90/2.18, or an actual F number of 41 (or 45, as suggested above). Just determine the correct shutter speed for the subject a F45, and the film will be correctly exposed. Then, if its a long exposure, you can deal with reciprocity normally.

Michael Kadillak

13-Aug-2017, 19:57

Goodness. Forget the frigging math. Have the subject hold a Calumet bellows correction wafer on her cheek and measure it with the corresponding ruler on the GG. DONE. It does not matter what the lens is or the format or anything. The proof is in the pudding.

For the life of me the willingness and ability of people here to make this excessively move complicated that needs to be is mind boggling. The objective here is to make photographs. This is not math class. Onward!

There is a lot of unnecessary calculation going on in this thread. Just remember this formula: f number = focal length divided by internal lens diameter (more properly called entrance pupil). Lets call that F = fl/p. For most LF lenses you can simply measure the entrance pupil with a ruler and you will be pretty close, but it is also possible to calculate it if you have two of the three numbers, as lungovw has above. So

fl = 24, F=11, so p = 24/11 or 2.18.

Now the trick to all this is to remember that the fl stamped on the lens is its focal length at infinity. But in your case, you are not using the lens at infinity, you are using it at 90 inches, Consequently, your focal length for this image is 90 inches!

So, pop that in our equation (F = fl/p) and it becomes F = 90/2.18, or an actual F number of 41 (or 45, as suggested above). Just determine the correct shutter speed for the subject a F45, and the film will be correctly exposed. Then, if its a long exposure, you can deal with reciprocity normally.

Jim,

Respectfully, I disagree. The gyrations that have been suggested over the years for understanding a very, very simple relationship are just amazing.

All to avoid dreaded MATH. (Shudder!).

What is so hard to comprehend? What is so hard to do?

The length of the bellows when extended.

Divided by the lens focal length.

Squared.

That's all there is to it. One silly measurement.

That's the Bellows Factor. Thats the amount the exposure needs to be increased.

1. Two.

2. Four

3. Eight

4. Sixteen

5. Thirty Two

Those are f/stop relationships. Pick the value closest to the Bellows Factor. Guess an in-between value when necessary. How many steps were necessary to get to that value? That's the number of f/stops to open up.

This is not higher math. It's not hard.

If the Bellows Factor is eight, we need 3 stops more exposure.

If the Bellows factor is 20, we need more than 4 stops, but less than 5 stops. Call it 4-1/3 stops. Take the shot.

It's a direct, basic embracing of the actual situation.

Just measure the darn bellows and everything else falls into place.

Anyone who does it two or three times will never forget it. The only special piece of equipment needed is a little tape measure. I carry a spring-loaded cloth one made for sewing. It doesn't weigh a thing. Takes up no room in the camera case. Very low tech. Works great.

Rich

Tim Meisburger

14-Aug-2017, 03:25

Interesting. So by direct calculation I end up needing two stops, and you three. I hope the OP reports the final result! (its such a large sheet of film, I think I would mount a 4x5 reduction back and then test. But I'm cheap!).

Jerry Bodine

14-Aug-2017, 14:14

...I hope the OP reports the final result!...

I hope so too, Tim. We've not heard from him since he first posted his questions. Perhaps he's out actually shooting.

FWIW, years ago, I set up my Sinar Norma at home to check out where on the lens to measure for the bellows extension; I did this for each of my lenses (3 Symmars and 3 Super Angulons) focused on infinity. Found that all the Symmars could be measured to the aperture control ring and all the SA's could be measured to the front of the lensboard. Then I made up a small chart of exposure factors calculated at incremental bellows extensions out to the bellows limit. It includes all six lenses. I keep that little chart in my field notebook (that is always with me); it saves having to do the calcs in the field, avoiding possible errors. I, too, use a very small metal re-coiling tape measure. So I only need to measure the extension, look up the factor, then shoot. It's a very fast system. We all make choices for our workflow, that's mine.

BTW, I'm curious whether I'm the only one who's noticed that OP stated his lens has no shutter. I tried to help him a bit in dealing with that.

Jim Michael

14-Aug-2017, 20:08

From about 22 to 90 in f-stop inches is 4 stops.

Tim Meisburger

15-Aug-2017, 07:08

This tool (Quick Disk) also works well. I printed one and then laminated it with clear packing tape, and it lives in my camera bag. http://www.salzgeber.at/disc/index.html

This is a helpful thread, but I would love to see a photo of a 90 inch bellows extension. It must be quite breath-taking.

Jerry Bodine

15-Aug-2017, 09:11

This tool (Quick Disk) also works well. I printed one and then laminated it with clear packing tape, and it lives in my camera bag. http://www.salzgeber.at/disc/index.html

Tim, that certainly is a useful convenient tool. I carry it as well, and it handles the bulk of any close-ups I do. But it is limited to only a two-stop correction.

Luis-F-S

15-Aug-2017, 15:38

From about 22 to 90 in f-stop inches is 4 stops.

Yes it takes about five seconds to figure that out. I can't believe we're still talking about this

FrancisF

15-Aug-2017, 19:43

Thanks to all for the insights and suggestions. I shall try Rich's formula first.

I will be happy to share the results here.....but that is a quandry. It will be a tiny image that can only really be appreciated in person.

Francis Fullam

Chicago, IL

Jim Galli

15-Aug-2017, 20:22

What Tim said in the second post. Measure the hole. Measure the length. Divide. Easy-peasy. 2" hole, 90" extension f45. 1 inch hole 90 inch extension f90. 1 1/2" hole, class? right, f64 No need to make it any harder.

Jim Becia

17-Aug-2017, 10:21

Yes it takes about five seconds to figure that out. I can't believe we're still talking about this

What Jim and Luis state. This is without a doubt, the easiest method. It's simply 4 stops going 22(24) inches to 32, 32 to 45, 45 to 64, 64 to 90.

Hullo FrancisF..

I strongly doubt that in a "shaded area" you have an answer from lightmeter of 1/1000 s. at f. 11. Just remember the f. 16 rule in full sun with shutter speed reciprocal of film ASA.. Therefore in full sun you should have this reading: f. 16 @ 1/125 s. Given you taking the picture during the midday hours..

I would check first how correct the reading of lightmeter is (battery ?)

If the subject is in an "open shadow" (i.e shaded by tall building w/out strong reflection from nearby water or glass building) I would open iris up to f. 4 or use 1/8 s. shutter speed if appropriate.. F. 4 @ 125 s. or f. 16 @ 1/8 s. are the starting points to THEN make all calculations advised above ..

Best

Mauro

jwallace68

21-Mar-2018, 19:11

Um.. what about the "no shutter" part of the description? A fractional shutter speed is going to be a challenge using the lens cap..

- JasOn

Michael Kadillak

25-Mar-2018, 06:15

In retrospect the photographer has three critical areas in this objective that need certainty because in 20x24 format mistakes are very costly. First he needs to verify the correct base exposure which seems anomalous to me as stated. Spot meter caucasian skin and place on zone 6. The second driver in this instance is he has a barrel lens and needs longer exposure times he can manage properly. I would shoot for about one second because that is the baseline for this application. Maybe someone has skill to pull off a half second with a barrel lens -then I tip my hat to them figuratively speaking. Lastly as I previously stated reading an easily seen square wafer at the plane of focus with a proper scale on the ground glass is uniquely simplistic and takes all of the "though" gymnastics out of the process. The scale immediately tells the photographer the bellows correction that is optically in play - any lens, any camera, and any magnification. Been using this for years on 8x10, 11x14 and 8x20 and it has never let me down. If there is one thing I have learned with ULF and that massive expanse of ground glass that needs considerable time to ensure it is all dialed in is "keep it simple" because while the images it produces are the reason we go down this road, the chances for little errors that can muck up an image increase proportionally with format size.

Hoping the photographer was able to get his shot.

Hi Rich,

I recently bought a Korona view 11x14" / refurbished

As I am very new to all of this. And i Have no films yet. Only reading and learning :)

I also still wonder how to calculate the right shutter speed accordingly the how much I extend my lens away from the "film level"

In your formula you wrote:

the length of the bellow ...measured from where to where? Lens ground plate to the Film? I measure in cm

Divided by the lens focal length. I use a Schneider Kreuznach Symmar S 360mm f6.8 . ... so i stick to 360mm in the calculation? or will these mm change soon as move the bellow?

ALSO: if my lens starts with f6.8 my first stop would start with f6.8 then instead of 2, 4, 8, ... up to f90 ? do i get this right?

1 stop = 2x.

2 stops = 4x.

3 stops = 8x.

4 stops = 16x.

how do I involve the ISO with the whole calculation... also for later on with wet plates?

Filmes I will get for the first go's will have ISO50 :)

thanks for helping

farid

Bob Salomon

10-Aug-2019, 13:59

2x magnification requires 4 stop additional exposure. So 1/60th.

Dan Fromm

10-Aug-2019, 14:11

Farid, I've already suggested that you buy and study a copy of Lester Lefkowitz' book The Manual of Close-up Photography. It has the answers to your questions about extension, and more.

Your later question suggests that you're not acquainted with the idea "light meter." You need one. You need to know how to use it.

In other words, learn the basics so that you'll be able to think for yourself. I think I gave you a link to the list. It has a section on books on LF photography that are often recommended to beginners. Buy one of them and study it.

hi Dan, let me check again thanks... i found that list.. but where to start :)

thanks

farid

It has a section on books on LF photography that are often recommended to beginners. Buy one of them and study it.

which one would you get if you were me? I live in switzerland so it will be a foreign book store order...

cheers

farid

Bob Salomon

10-Aug-2019, 15:02

Rather then worrying about focal length, bellows extension it is much easier to learn about magnification.

½ lifesize - open 1 stop.

1:1 lifesize - open 2 stops.

2:1 twice lifesize open 4 stops.

To make it easy put a ruler in the scene by the subject and measure an increment on the gg.

Dan Fromm

10-Aug-2019, 17:25

which one would you get if you were me? I live in switzerland so it will be a foreign book store order...

cheers

farid

The ones recommended are all good. I have Stroebel. Look for sellers on abebooks.com, alibris.com, amazon.com, bn.com, ... Also try Amazon sites in the EU, e.g., amazon.de.

Hi Dan

just ordered one from .. Lebowitz or similar.. i also got a german one from a swiss guy called Peter Michel "Kollodium" . very precise lots of different kollodium recipies temperature calculations etc.. will start reading today. https://www.fotokultur.ch/shop/das-kollodium/ her also does courses and workshops. Will attend to join in october if i manage.

thanks

Powered by vBulletin® Version 4.2.5 Copyright © 2020 vBulletin Solutions Inc. All rights reserved.