Results 1 to 9 of 9

Thread: G Claron 210/240 Copal 1 swap

  1. #1
    Stephen Vaughan
    Join Date
    Aug 2001
    Location
    Bath, UK
    Posts
    60

    G Claron 210/240 Copal 1 swap

    I have a 210 G Claron in a Copal 1 shutter. I also have a 240 G Claron which I would like to mount in the same shutter. If I do this can I use the same aperture scale? i.e. do the apertures correspond in size between the two lenses? Or, do I have to get a scale specifically for the 240? Many thanks as always........

  2. #2

    G Claron 210/240 Copal 1 swap

    You can do what you wish. There is a correction factor of 1/3 of a stop. The 240 len is 1/3 of a stop more closed down than indicated. ie, When using the 240 in this instance, if the iris says F11, the actual stop is F12.5. Having even more fun, the equal focal length 1/3 stop increments are.... 210mm, 240, 270, 305. Sound familiar?

  3. #3
    Stephen Vaughan
    Join Date
    Aug 2001
    Location
    Bath, UK
    Posts
    60

    G Claron 210/240 Copal 1 swap

    Thanks Frank - at the moment the 240 lens is in a Copal Press shutter and the 210 is in a standard Copal shutter. When I compare the apertures between the two it seems the 240 is at least a 1/2 stop wider (possibly slightly more - but definetely more than a 1/3). How do I standardise the two lenses? Thanks......

  4. #4

    G Claron 210/240 Copal 1 swap

    The factors between the 210 and 240 are a mathematical and physics solution. In other words, they are correct. If you think otherwise by looking through the glass, go right ahead. Let me suggest trying a test... shoot a blank sky with both lenses. Develop the negs, then measure the transparent density of the negs. Then you have the scientific answer. I had a complete set of G-Clarons. 210, 240, 270, and 305. It works.

  5. #5

    Join Date
    Jan 2002
    Location
    Besanšon, France
    Posts
    1,278

    G Claron 210/240 Copal 1 swap

    Stephen. If you are ready to swap your shutters, then you are also ready to measure the actual diameter of the iris without glass. Measure the actual diameter of the iris with the 210 scale at f/9. Screw the front element of the 240 and try to find the position of the aperture control that opens to the max aperture of the 240. Say : this would correspond to f/6.3 in between 5.6 and 8.
    I assume that you can actually open the iris beyond the F/9 engraving designed for the 210, and that there is no mechanical limit preventing to open wider than that.
    Now you know the physical diameter of the iris for the 240 at F/9 and the ratio between both physical diameters @f/9 on the "210" scale and on the future "240" scale to be recomputed. But this is just for cross-checking the procedure, in fact. F-numbers are inversely proportionnal to the physical diameter of the iris. So if actual f/9 (max aperture) for the 240 reads f/6.3 on the scale designed for the 210, all engravings have to be re-computed by applying the 9/6.3 correction factor to all "210" readings. So now f/11 on the "210" scale will correspond to 11*9/6.3 ~ 16 on the new "240" scale. You can cross-check this conversion ratio with the ratio of physical diameters, since you have to unscrew both lens elements, you can measure it easily.

    If somebody needs to estimate the real f-stop number without un-screwing the lens elements, the optical engineer will make an image of the iris as seen from the front, this is called the entrance pupil. Measuring the actual diameter of the entrance pupil yields the true f-number equal to the focal length divided by the diameter of the entrance pupil. You do not have access physically to the entrance pupil which is located inside the glass, however you can make an image of this pupil with a known magnification ratio and measure the final image.

  6. #6
    the Docter is in Arne Croell's Avatar
    Join Date
    Dec 1997
    Location
    Huntsville, AL and Freiburg, Germany
    Posts
    1,085

    G Claron 210/240 Copal 1 swap

    For a lot of lenses (but not all*) the wide open aperture is often not only defined by the aperture diaphragm, but also by parts of the lens cell mount. For plasmats, like G-Clarons, this is the mount rim of the innermost lens of each cell. One can see this when looking through the mounted lens from the front, shutter open, and closing the aperture. Essentially, you look at the entrance pupil. Initially (outside the engraved aperture scale) the diaphragm blades are not visible. They should just became visible when the stated open aperture is reached on the scale, f/9 in your case. At that point the diaphragm opening and the stop defined by the lens mount are identical. If this is the case, and you have the same type of lens, as with your G-Clarons, just swap the lens cells, and note at what position of the aperture lever the blades just appear seen through the front cell for the new set. That is your new f/9. If the difference to the old position is not too big it is often enough to loosen the screws holding the f-stop scale and shift the scale a bit. Or, if that is not enough, lengthen the holes for the screws with a needle file.

    *This method works for most lenses, nearly all modern ones, but not for all, since it really depends on the fact if the manufacturer provided a "stop calibration" with the lens mount. Notable exceptions are often wide angle Gauss lenses (WF Ektar, G-Claron WA). If the original mount had an additional mechanical stop (e.g. a screw) to keep the aprture lever from opening all the way, it certainly does not work.

  7. #7
    Andy Eads
    Join Date
    Jul 2001
    Location
    Pasco, Washington - the dry side of the state
    Posts
    163

    G Claron 210/240 Copal 1 swap

    Copal #1 shutters have a nice design feature that has carried from model to model. Every 8 degrees of movement on the aperture scale causes a one stop change in aperture. Once you nail one f/stop, the others fall into place. Good luck!

  8. #8

    Join Date
    Jan 2004
    Location
    Halifax, Nova Scotia
    Posts
    440

    G Claron 210/240 Copal 1 swap

    Stephen,

    What is wrong with the Copal Press shutter? Is it slow? Inaccurate? I have a lens in a Prontor Press shutter and I love it. I plan on purchasing a 240mm G-Claron and to save money I was planning on picking up a Ysaron or Tominon in a press shutter and swaping out elements. Do you think this is a bad idea? Why?

  9. #9

    Join Date
    Sep 2003
    Location
    Harbor City, California
    Posts
    1,753

    G Claron 210/240 Copal 1 swap

    For a camera which will always be used on a tripod, I like self-cocking shutters.. When would you ever need the higher speeds? I'm not enthisiastic about those which lack a press focus function, though.

Similar Threads

  1. Fitting G-claron cells on a Copal shutter
    By Luca Merlo in forum Lenses & Lens Accessories
    Replies: 9
    Last Post: 14-May-2006, 06:49
  2. 240 f9 G-claron/copal press#1
    By ronald lamarsh in forum Lenses & Lens Accessories
    Replies: 2
    Last Post: 4-Oct-2004, 20:17
  3. 355 G Claron Shutter Swap
    By Kevin Crisp in forum Lenses & Lens Accessories
    Replies: 6
    Last Post: 29-Jun-2004, 19:39
  4. copal 1 shutter - can I swap lens sets?
    By bill_1041 in forum Lenses & Lens Accessories
    Replies: 7
    Last Post: 26-Sep-2003, 08:02
  5. 19th PPF Sprint Photo Swap Meet: Portland, Or. Sat, 3/17/01
    By neil poulsen in forum Announcements
    Replies: 0
    Last Post: 11-Mar-2001, 11:44

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •