Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: A Calumet 400 and a Polaroid/Fuji back?

  1. #1

    Join Date
    May 2011
    Posts
    8

    A Calumet 400 and a Polaroid/Fuji back?

    Once again, I am trying to get my Polaroid 405 back to work with my Calumet CC-400. I've just spent some time using it on a Toyo field camera, and I wish I could use it on the Calumet. It seems to be perhaps a quarter of an inch too thick to fit into the spring back of the Calumet.
    After reading an older thread here, I contacted Jose Pueyo, the expert at Calumet. The thread had suggested using springs with the part numbers 105797 and 105798, however, after sending photos of my camera to Jose, he said that it had those springs already. Unfortunately, he had no firm suggestions, though he thought that washers under the spring to give a little more clearance might work. That would also require a longer screw to secure the spring.
    Has anyone else had any successful experience with this problem? I would greatly appreciate any suggestions, keeping in mind my limited knowledge here!

    JK

  2. #2
    Unwitting Thread Killer Ari's Avatar
    Join Date
    Apr 2009
    Location
    Ottawa, Canada
    Posts
    6,286

    Re: A Calumet 400 and a Polaroid/Fuji back?

    I've read about longer springs that do allow use of the Pola back.
    Maybe Jose is wrong, if he's working from photos only.

    On my shitbox B&J, I removed the lower springs to permit use of the Polaroid back.

  3. #3
    Mike Anderson's Avatar
    Join Date
    Jan 2010
    Location
    San Diego
    Posts
    681

    Re: A Calumet 400 and a Polaroid/Fuji back?

    Later versions (black ones) have a deeper bale and will take the pack film holders. Now I'm not positive that all black ones have the deeper bale, but if someone could confirm that they do you could just buy the cheapest black one you can find and transfer its GG/bale assembly to your camera (that's what I did). The 2nd camera would provide various knobs and screws and parts if you need them. Or just use the black camera as your main camera and use your existing camera for parts. Here's a black 22" version for $89:

    http://www.keh.com/camera/Large-Form...990846210?r=FE

    ...Mike

  4. #4

    Join Date
    Dec 2003
    Posts
    247

    Re: A Calumet 400 and a Polaroid/Fuji back?

    you could just buy ebay #130560257615 10 Abbatron HHSMITH Nickel plated brass Standoff 4-40
    then take off the springs put in 4 of the Standoff & put the springs you now can use the 405 back

  5. #5
    Pastafarian supremo Rick A's Avatar
    Join Date
    Feb 2010
    Location
    Laurel Highlands, Pa., USA
    Posts
    790

    Re: A Calumet 400 and a Polaroid/Fuji back?

    I have a cc-400 and cc-401, I used a Pola 405 back on both cameras before selling the back. Try stretching the springs a bit, IIRC mine was a very snug fit the first time I used it.
    Rick Allen

    Argentum Aevum

    practicing Pastafarian

  6. #6

    Join Date
    May 2011
    Posts
    8

    Re: A Calumet 400 and a Polaroid/Fuji back?

    That's brilliant. I have to admit I didn't know what Jose meant when he said the screws holdng the springs were 4-40, but you certainly do! So I just use the standoffs as spacers below the springs? Do you know that that will be the right size, or are you going by my guess of a quarter of an inch (I'm not at all sure how exact that is)?

  7. #7

    Join Date
    May 2011
    Posts
    8

    Re: A Calumet 400 and a Polaroid/Fuji back?

    And generally, thanks for the quick, very helpful answers. I will try the $6 standoffs before the second body for $87, but they are all helpful and possible solutions. I'll be happy for any others, too.
    JK

  8. #8

    Join Date
    Dec 2003
    Posts
    247

    Re: A Calumet 400 and a Polaroid/Fuji back?

    I just tryed AND its not going to work!!!
    NEED 3/16 to get my P back in BUT THE GROUND GLASS WONT TUCH
    for you to focuss then I tryed just 1 nut under the springs SAMETHING

  9. #9

    Join Date
    Dec 2003
    Posts
    247

    Re: A Calumet 400 and a Polaroid/Fuji back?

    even if you changed the bale it would need larger springs TOO!!

  10. #10

    Join Date
    Jul 2010
    Location
    Minneapolis, MN
    Posts
    169

    Re: A Calumet 400 and a Polaroid/Fuji back?

    I seem to remember that Calumet still sells a set of longer springs for the CC-400 series that is for just this purpose-to allow the ground class to get a little further away and allow a pack film back to fit. Check their website.
    Reid

    http://www.flickr.com/photos/rjbuzzclick/

Similar Threads

  1. Newbie Calumet 400 Lens Options
    By calumetorbust in forum Cameras & Camera Accessories
    Replies: 9
    Last Post: 10-Oct-2011, 23:15
  2. T20 Reflex Viewer on Calumet cc 400
    By Howard M in forum Cameras & Camera Accessories
    Replies: 0
    Last Post: 5-Aug-2008, 20:57
  3. Lensboard retention woes on a Calumet 400 series 4x5
    By John O'Connell in forum Cameras & Camera Accessories
    Replies: 5
    Last Post: 4-Dec-2000, 08:19
  4. Calumet 400 and Grafmatic
    By s. gregory in forum Cameras & Camera Accessories
    Replies: 4
    Last Post: 10-Oct-2000, 19:42

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •