Results 1 to 6 of 6

Thread: developing litho/orthofilm

  1. #1

    developing litho/orthofilm

    I am using kodak EL film as final medium. I proces the film with Dektol diluted 1:10. I am having problem of uneven development espetially smooth erea such as sky. I tryed different agitation methods, but didn't work. I am thinking of using print processors. If any one has idea of method to develop litho/ortho type film evenly, please he lp me. Or suggest me which processor is the best. I need at least 16" wide.

  2. #2

    developing litho/orthofilm

    Hi, Easiest answer of the day! I've been in the lithographic industry for 40 years and have developed lith film in most every thing. The best is Kodak A B Lith developer. Follow the directions. Usually 3 min. @ 68 degrees. I think your Dektol problem is dilution. Don't. In my home photo darkroom I do this: 2 min. in straight Dektol @ 68 degrees. Lith film is an extremely high contrast material. Images are either black or white. Period! No (or very little) midtones possible. Work under a red safelight and you can watch the image pop up. But give it at least 2 full min. in the soup. Fix. Wash. Drink beer.

    Voiola! Fini! At no time do my fingers leave my palms. Send beer!

  3. #3

    Join Date
    Dec 1997
    Location
    Baraboo, Wisconsin
    Posts
    7,742

    developing litho/orthofilm

    Since he's diluting it 1:10 I suspect he is seeking a "normal" looking negative rather than the typical "black and white" lith negative. At least that's the usual reason for developing lith film in highly diluted Dektol. However, 1-10 does sound extreme and especially with very large sheets of film developer exhaustion may be the cause of the problem. I'd try a more concentrated dilution. I used to develop Arista lith film in Dektol diluted about 1-4 as I recall, and also in D 76 developed 1-6 I believe (it's been a few years). However, I didn't use Kodak EL film so I don't know how either of these would work with that film though they should be worth a try. I don't remember having any problems with uneven development.
    Brian Ellis
    Before you criticize someone, walk a mile in their shoes. That way when you do criticize them you'll be
    a mile away and you'll have their shoes.

  4. #4

    developing litho/orthofilm

    Gen,

    Sounds to me like you could do with using a bigger tray to avoid the effect of agitation ripples near the edges. You can see the variation in open areas like the sky but it might also be present in areas of busier information. Rule of thumb: Tray one size up from material.

    From the chemical viewpoint more solution may be an answer. With such dilutions you must be sure to have sufficient stock solution to fully develop the surface area of film/paper. If your material is 16 inches wide that could require quite a sizeable volume of solution with the Dektol at 1+10.

    Just a thought or two ... WG

  5. #5

    developing litho/orthofilm

    Hi, If you are looking for low contrast results, try looking at cameramakers@rosebud.opusis.com , They have just had several responces on developing Lith (Kodak and Arista) film to make printable photos.

  6. #6

    developing litho/orthofilm

    I have played with Arista Lith film for unsharp and/or contrast reducing masking. I've used Dektal @ 1:2 2min;1:10 2 min;1:20 2 min. interesting but useful curves. 1:10 and 1:20 give a nice smooth curve of about CI +/-.3-good for masking. Development in 5x7 tray seemed uniform. George

Similar Threads

  1. 5x7 c-41 developing in NYC
    By michael waldron in forum Darkroom: Film, Processing & Printing
    Replies: 3
    Last Post: 24-May-2002, 13:27
  2. Has anyone used Ortho Litho film?
    By Emile J Schwarz in forum Darkroom: Film, Processing & Printing
    Replies: 8
    Last Post: 7-Feb-2001, 09:30
  3. Developing T-Max 100 with D-23
    By Delfino L. Tiongco in forum Darkroom: Film, Processing & Printing
    Replies: 3
    Last Post: 10-Feb-2000, 18:02
  4. Litho??
    By Raven Garrow in forum Style & Technique
    Replies: 2
    Last Post: 18-Oct-1999, 00:48
  5. developing 4x5, help
    By Raven Garrow in forum Darkroom: Film, Processing & Printing
    Replies: 11
    Last Post: 12-Mar-1999, 21:02

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •