Results 1 to 9 of 9

Thread: Diffusion material for unsharp masking

  1. #1

    Join Date
    Jun 1998
    Location
    Jerusalem
    Posts
    149

    Diffusion material for unsharp masking

    I'm about to take the plunge into Unsharp Masking. I have read that I should place diffusion material between the neg and the maski ng film when exposing the mask (3mm diffusion?) My question is - Should this material be clear or opaque? Many thanks to everyone for all the wonderful info on this board.

  2. #2

    Join Date
    Aug 2000
    Location
    France
    Posts
    151

    Diffusion material for unsharp masking



    Yaakov,



    the Radeka Masking Kit e.g. uses Kodak Duratrans as diffusion material for that purpose. Just place an unexposed sheet into the fixer. For an unsharp mask, you must either use a diffusion material or a spacer glass in order to get an unsharp mask



    Regards,

  3. #3

    Join Date
    Jun 1998
    Location
    Jerusalem
    Posts
    149

    Diffusion material for unsharp masking

    Thanks Thilo!

    I know that the Duratrans is supposed to go above the negative to diffuse any collimated light from the enlarger. Is it also supposed to go between the neg and the mask film? Also - it's no way 3mm. Are you supposed to put several sheets between the two to make up the thickness?

  4. #4

    Join Date
    Aug 2000
    Location
    France
    Posts
    151

    Diffusion material for unsharp masking

    Yaakov,

    Duratrans is suitable for unsharp masks, too. The diffusion material yields the same effect as a spacer glass would. Generally, you can use any combination of diffusion materials and spacers. Two sheets of Duratrans yield a more unsharp mask than one sheet, as would a spacer glass of 4mm compared to one with 2mm thickness. The degree of unsharpness is a variable parameter and it depends on the enlargement factor and the quality of the negative/positive. There is no general rule for this. You'll have to do some experiments by yourself and learn to judge by experience.

    Regards,

  5. #5
    Robert A. Zeichner's Avatar
    Join Date
    Feb 1999
    Location
    Southfield, Michigan
    Posts
    1,090

    Diffusion material for unsharp masking

    The handiest spacing material for unsharp masking is clear acetate. This can be sourced from most good art and drafting supply houses and comes in pads with interleave sheets that are very convenient and keep the film clean. You will probably find that you don't need any spacer between the neg and the mask as the thickness of the base material of the neg is usually enough to achieve the desired effect. You will probably want to use some frosted drafting film between the light source and the sandwich while making the exposure of the mask in order to keep the illumination absolutely even.

  6. #6

    Join Date
    Dec 1997
    Location
    Baraboo, Wisconsin
    Posts
    7,697

    Diffusion material for unsharp masking

    i wouldn't put anything between the negative and the film. It adds another layer of things to collect dust and scratches. If you read Howard Bond's two articles on unsharp masking that appeared in Photo Techniques magazine a few years ago, you'll see that in the first article he said to use something between the negative and the film, then in the second article he changed his mind, concluded that it wasn't necessary. The only purpose of putting anything between them is to create a slight space so that the mask will be unsharp. However, Bond concluded that the space created by the back of the film and the mask (or something like that, it's been a while since I read the articles) alone was sufficient to make the mask unsharp so that nothing else was needed. Since reading his article I've stopped using anything in between the film and the mask and things have worked fine. If, however, you nevertheless wish to use something, you can go to any art supply store and buy a sheet of .003, .005, or .009 mylar and use that.
    Brian Ellis
    Before you criticize someone, walk a mile in their shoes. That way when you do criticize them you'll be
    a mile away and you'll have their shoes.

  7. #7

    Join Date
    Dec 2001
    Posts
    103

    Diffusion material for unsharp masking

    I wonder how good a digitially made mask would be for alternative processes and contact printing. I'm thinking I could print masks onto transparencies (we have excellent printers at work). Or would the results be too inferior to masks made with lith film? Just curious.

  8. #8

    Diffusion material for unsharp masking

    Why on earth would anyone wan't to make a Large format picture unsharp? Can't you just make a picture with a digital kamera and prosess it in Photoshop untill the required image occur?

  9. #9

    Join Date
    Dec 2001
    Posts
    103

    Diffusion material for unsharp masking

    Ummmm why not? It's just idle curiosity, and maybe something novel to try. By the way, it is not for making the picture less sharp as the name would suggest, it is a way of fiddling selectively with the contrast.

Similar Threads

  1. What Program Do You Use For Unsharp Masking?
    By Scott Rosenberg in forum Digital Hardware
    Replies: 22
    Last Post: 15-Feb-2005, 15:35
  2. Unsharp Masking
    By scott jones in forum Darkroom: Film, Processing & Printing
    Replies: 9
    Last Post: 22-Dec-2001, 11:30
  3. Unsharp masking - Assistance please
    By Steve Feldman in forum Darkroom: Film, Processing & Printing
    Replies: 6
    Last Post: 25-Nov-2001, 01:06
  4. unsharp masking
    By james mickelson in forum Darkroom: Film, Processing & Printing
    Replies: 1
    Last Post: 2-Nov-1998, 22:54
  5. Unsharp Masking Techniques
    By JoEl BerBer in forum Darkroom: Film, Processing & Printing
    Replies: 1
    Last Post: 29-Jul-1998, 23:38

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •