Results 1 to 10 of 10

Thread: Residue on negatives

  1. #1

    Residue on negatives

    I have a particularly persistent problem with B&W sheet film that I process. Af ter hypo clearing, I wash in water for 15 minutes in water that has gone through an in-line filter. Then I soak and slightly agitate in Wal-Mart distilled water with 2 drops of photo-flo, forma-flo or LPN solution. I then hang dry in my da rk room without squeegeeing. The film has drying marks similar to what you woul d see on a plate that dried in the sun, also sometimes I see fingerprints that g ot there when I was loading the film. I am not sure how to get rid of this resi due. It shows up as streaks in the sky and blank areas of the print. I have tri ed varying the soaking time and the amount of photo-flo, but it does not seem to make a difference. I am also not sure whether I can load film with gloves on, I hear it is very difficult. Any suggestions are greatly appreciated.

  2. #2

    Join Date
    Feb 2001
    Location
    Greenbank, WA
    Posts
    2,605

    Residue on negatives

    Between LPN and Photo-Flo, I think LPN works MUCH better. I am not familiar with the other product. I have found that LPN in distilled water can work fine at much less concentration than indicated in the tiny print on the bottle. (Does it say 2 drops per pint?) I use 1 drop per quart and it still does the job. And don't forget that the solids in the water on the negatives when you put them in the solution tend to build up in it. I suggest a greater dilution. You can pour some of the solution over the face and back of the negative to make sure you don't get bubbles or waves of solution. There will still be very faint lines that dry on the negative, but they are small enough that with a cold light they don't show.

  3. #3

    Residue on negatives

    Andrew: I use a bit more photoflo with plain ol' tap water and dont have a problem. You might try wiping the negs gently before hanging them up. A cotton ball dipped in photoflo and squeezed out a little makes a good wipe for sheet film. Don't get heavy handed and you will not scratch the negs...just wipe the droplets off. The purpose of photoflo is to break the surface tension of the water so it runs off evenly. I just don't think two drops are enough.

    Regards,

  4. #4
    Beverly Hills, California
    Join Date
    Feb 2000
    Location
    Beverly Hills, CA
    Posts
    1,108

    Residue on negatives

    Andrew, regarding drying marks: toss your developer, stop, fixer, etc. and remake ALL solutions with your Wal-Mart distilled water. That in-line filter you are using is not fine enough to filter out the disolved calcium deposits in your tap water which undoubtedly are causing your drying marks. Do ALL your water rinses with distilled tap too. You will instantly find that your negatives will actually sparkle, and you will feel worthy again :>)

    Re: fingerprints, wash hands really well to remove oils, don't touch emulsion when possible.

  5. #5
    Beverly Hills, California
    Join Date
    Feb 2000
    Location
    Beverly Hills, CA
    Posts
    1,108

    Residue on negatives

    ....distilled water too (not distilled tap too)

  6. #6

    Residue on negatives

    Some solvent developers will do this due to the alkalai used. What developer are you using? Some might need different stop baths and fixers.

  7. #7

    Join Date
    Apr 2000
    Posts
    149

    Residue on negatives

    I think Kevin was referring to LFN, Edwal's low foam wetting agent. I agree that it is far superior to Photo-flo. I use only 2 drops in a liter of water and haven't had drying marks on my film in a long time. A small bottle lasts for years.

  8. #8

    Residue on negatives

    I agree with Ed, LFN is the best. And please don't shop at Wal-Mart anymore. Support downtown businesses, not sprawl.

  9. #9

    Join Date
    Feb 2001
    Location
    Greenbank, WA
    Posts
    2,605

    Residue on negatives

    Ed is right, I meant LFN, I just blindly copied what you had in the question. I assume you meant LFN.

  10. #10

    Residue on negatives

    Thank you all for your thoughtful answers. I will try them and report back my results on the thread.

Similar Threads

  1. Best way to store 4x5 negatives
    By brian steinberger in forum Darkroom: Film, Processing & Printing
    Replies: 8
    Last Post: 13-Feb-2006, 11:53
  2. They Want My Negatives......
    By domenicco in forum On Photography
    Replies: 18
    Last Post: 14-May-2002, 17:39
  3. testing washed prints for fixer residue
    By rebecca_2713 in forum Darkroom: Film, Processing & Printing
    Replies: 6
    Last Post: 14-May-2002, 01:02
  4. Heavy Residue on 4x5 Negatives after Processing
    By Andre Noble in forum Darkroom: Film, Processing & Printing
    Replies: 17
    Last Post: 26-Jul-2001, 02:27
  5. Spots on negatives
    By Robert A. Zeichner in forum Darkroom: Film, Processing & Printing
    Replies: 6
    Last Post: 2-Jan-2001, 00:31

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •