Results 1 to 5 of 5

Thread: Which developer works best with Tri-X 8x10 sheet film???

  1. #1

    Join Date
    Mar 1999
    Posts
    11

    Which developer works best with Tri-X 8x10 sheet film???

    Which developer works best with Tri-X 8x10 sheet film considering grain, tonal character, speed, etc. . .for JOBO rotary process?? D76(1:1), D23, Xtol, Microdol-X, Ilfosol-S, (except HC-110)

    I've been using T-Max400/T-Max RS and having a hard time to control the light on highlights(nudes) under studio lighting situation(Soft Box). Highlights are somewhat blocked and losing details on skin.

    Then, I'm planning to run some tests on Tri-X with different developer. Since with Tri-X grain is more noticelable and low in resolution compared with T-Max I need to draw as much quality as I can from Tri-X. (I make mural prints, so both grain size and sharpness are very important while using Tri-X)

    If you could share what you have, time, temp, rotation speed, EI, dilution, ... , I will appreciate it!! Thanks in advance riichi

  2. #2

    Which developer works best with Tri-X 8x10 sheet film???

    riichi

    Are you ready for this?

    D-76 diluted 1:1 or full strength.

    I have also used split D23: first bath 12 minutes 2nd bath 3 minutes and rated the film at 200. This gives me a wider tone,"Stronger" negative for making Palladium/Platinum prints. With 8x10 grain is not an issue, but tonality is and all the fancy soups in the world can not beat these two for reliablity and effect. The only thing that comes close is PMK, which has a full set of safety drawbacks as well as tonality advantages, esp. for Platinum prints.

    Cheers

  3. #3

    Join Date
    Feb 2001
    Location
    Greenbank, WA
    Posts
    2,605

    Which developer works best with Tri-X 8x10 sheet film???

    Riichi: Sorry you don't want to hear it, but my first choice would be HC110, Dil "B" 6 minutes at 68 degrees F. After 15 years I keep coming back to it. Also, Rodinal 1:50, 12 min. @ 68 degrees is very nice too. My EI index would be meaningless to you unless I lend you my meter. These two combinations and times produce equally dense negatives, at least for me. Rodinal is known for good highlight separation and my experience supports this in an unscientific way. These are tray development times, so I'm sure you'll need to adjust them for the tube. My "magic bullet" is paying attention to what I'm doing and composing the picture well. There will be no lack of quality with the above combinations, nor, I'm sure, with 20 others you could try. I highly recommend taking the time to do the necessary zone controls, determine your personal exposure index and development time.

  4. #4

    Join Date
    Oct 2000
    Posts
    120

    Which developer works best with Tri-X 8x10 sheet film???

    Hi Riichi, A lot of people seem to agree that HC-110 Dil. B is the best acutance developer for Tri-X. It's a high definition, non solvent developer which increases sharpness at the expense of moderate grain. With 8x10, you don't need to be unduly concerned. D76 when diluted 1:1 is also an acutance developer whereas undiluted, it's a moderately fine grain solvent developer. If you insist on D76, I'd use it 1:1 with a corresponding time increase. This would also help with the highlights blocking when using a continuous agitation processor like the Jobo. Hope this helps, Henry

  5. #5

    Which developer works best with Tri-X 8x10 sheet film???

    Well, I'll second the remarks about D76 1:1 and HC110(dil B). Also worth considering is the pyro developer PMK, for scenes where the separation of highlight detail is important.

Similar Threads

  1. ilford delta 100 sheet film (kodak developer)?
    By gary in forum Darkroom: Film, Processing & Printing
    Replies: 2
    Last Post: 7-Feb-2006, 15:53
  2. Best suited developer for PlusX sheet film
    By J.R. in forum Darkroom: Film, Processing & Printing
    Replies: 5
    Last Post: 21-Oct-2005, 21:05
  3. Film developer for 8x10 and 35mm
    By Steve Williams_812 in forum Darkroom: Film, Processing & Printing
    Replies: 8
    Last Post: 5-Oct-2005, 12:03
  4. I need your empty 8x10 sheet film boxes - please
    By jesskramer in forum Cameras & Camera Accessories
    Replies: 1
    Last Post: 25-Sep-2004, 23:08
  5. What developer works best with T-Max 400 sheet film with rotary processer?
    By ric YAMA in forum Darkroom: Film, Processing & Printing
    Replies: 3
    Last Post: 24-Nov-2001, 00:56

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •