Results 1 to 4 of 4

Thread: 4x5 drum development questions

  1. #1

    4x5 drum development questions

    Hi,

    Well I went ahead and got myself a 4x5 Pacemaker Speed Graphic, and am now having some trouble trying to figure out how to handle development myself. After reading on the largeformatphotography.info site about using Unicolor drum and roller I thought that sounded about right for me. I was able to secure a Uniroller but actually finding an 8x10 Unidrum has proven to be quite difficult.

    Today I walked into a local camera store and found a Chromega 8x10 print processing drum so I bought it. This drum has three cylindrical tubes which run down its length and in between which you wedge the print/film. These are similar to the v-ridges in the Unicolor drum. The problem that I'm concerned about with this Chromega drum is that there are no ridges along the walls of the drum, so the backside of the film can touch the walls. When the film is loaded between the tubes the backside of the film gets very close to the walls of the drum. I've practiced loading the film several time and and can't find a way to insure that no part of the film is touch the wall of the drum. Now since most of the film isn't touching the wall, is that enough for the chemicals to get back there and do their job? The Uniroller reverses itself something like every 1.5 revolutions.

    So I'm wondering if this is ok for drum development, or will it cause problems with not enough of the chemicals reaching the back side of the film. Does anyone have any thoughts about this? Is presoaking the film likely to begin working on the anti-halation layer on the backside of the film?

    I noticed that in the manual for the BTZS tubes it looks like the film is actually touching the walls of the tube, so maybe this is ok??

    Thanks in advance, Derek

  2. #2

    4x5 drum development questions

    I don't know about thus particular drum, but I've used the equivalent Jobo print drum to develop 10x8 E6 and B&W film with no problems.

  3. #3

    Join Date
    Mar 2005
    Location
    Alaska
    Posts
    281

    4x5 drum development questions

    The Chromega drum should work fine. As you notice, the BTZS tubes are smooth, and the film back is in tight contact. Some people recommend a piece of fiberglas screen between the film and tube, but I’ve found that more trouble than it’s worth. The chemistry only needs to contact the emulsion side of the film. If you experience any “mottling” on the backside (usually in T-Max films), wash the film in trays with a clearing solution. I would also recommend a water presoak for more even results.

  4. #4

    Join Date
    Dec 1997
    Location
    Baraboo, Wisconsin
    Posts
    7,697

    4x5 drum development questions

    I've used BTZS tubes in 4x5 and 8x10 sizes for years. The fact that the back of the film touches the walls of your Unicolor drum won't be any problem. You can leave the film in the drum when you're using the stop bath but be sure to remove it and fix it in trays. The back of the film will look funny, very milky and splotchy, when you first remove it but after it's been in the fix for a while that will disappear.
    Brian Ellis
    Before you criticize someone, walk a mile in their shoes. That way when you do criticize them you'll be
    a mile away and you'll have their shoes.

Similar Threads

  1. Bergger BPF200 - Jobo Drum and +/- development
    By jantman in forum Darkroom: Film, Processing & Printing
    Replies: 4
    Last Post: 4-Oct-2005, 12:23
  2. Two questions about film development
    By brian steinberger in forum Darkroom: Film, Processing & Printing
    Replies: 6
    Last Post: 25-Aug-2005, 12:57
  3. over-development
    By Neal Shields in forum Darkroom: Film, Processing & Printing
    Replies: 9
    Last Post: 22-Apr-2004, 13:27
  4. Development times using Jobo Expert Drum
    By Mark Lipton in forum Darkroom: Film, Processing & Printing
    Replies: 5
    Last Post: 7-Jan-2002, 16:24
  5. Questions on Unicolor drum 4x5" processing
    By John H. Henderson in forum Darkroom: Film, Processing & Printing
    Replies: 12
    Last Post: 21-Jun-2000, 07:37

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •