Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Risk of fungus

  1. #1

    Join Date
    Oct 2017
    Posts
    1

    Risk of fungus

    Hello everyone. New user here on the forums as I'm about to move into 5x4 film photography, and need a bit of advice before I do.

    I am in the UK and have found a good shop with a knowledgeable proprietor, and good prices.

    For sale is a MPP field camera, complete with a lens "showing signs of fungus". My plan is to remove that lens, and replace it with a lens not showing sign of fungus.

    The camera apparently shows no signs of fungus, but my question to you guys is this: if the camera has been stored with a lens showing signs of fungus, is that camera a risk to clean lenses, even if it is not currently showing signs of a fungus invasion?

    I do not want to take a stupid risk and ruin a bunch of lenses, but nor do I want to miss an absolute bargain if I'm over-worrying on the issue.

    I plan to use a clear plastic box for storage, stored in a bedroom that is kept heated, and place silica gel in the box as a precaution. That aside, being a field camera, it will be used outside and outside in this country is often not so dry.

    Your thoughts would be appreciated, especially since I really need to conclude the deal in the morning if I possibly can.

  2. #2

    Join Date
    May 2015
    Location
    SooooCal/LA USA
    Posts
    1,001

    Re: Risk of fungus

    Don't fear, a camera that has some fungus can be treated easily... First, remove the back and give it a good sniff... If you smell fungus or maybe a sneeze, it's got fungus...

    If you place the semi opened camera in a plastic bag (with the bellows slightly extended, and back removed) and spray a piece of towel, paper towel, or sponge with a heavy dose of Lysol spray, and seal the bag with both inside... Suspend the camera on a block, etc so there is a space under, and don't allow any of the bag to touch any part of the camera during fuming... Leave bag in a warm to hot place for a week to 10 days, the heat will set-up convection currents that will help the disinfectant spread to all parts of the camera... Sniff again, and repeat first step if necessary... When done, wipe down with 99% alcohol, avoiding soft leather, or painted surfaces etc (to avoid damage)... This will remove the surface growth... Then treat leather with Lexol, or a good leather preservative containing lanolin... Then do the normal camera check steps like the torch (flashlight) in the bellows trick to look for leaks, and so on...

    Look at the surfaces of the lens on it with a loupe to see if there is any pitting from the fungus on them... Clean all the surfaces carefully with alcohol, and place it in another Lysol bag (like the camera bit) after unscrewing the front and rear element barrels, and to the bag not touching anything... Clean all metal surfaces, and final clean the glass with good lens cleaner...

    This should get you started, and once disinfected, your other lenses will be OK on it, but store this camera in a dry place for awhile when not using, and if there is a very warm sunny day, leave it out in the sun for awhile to really dry it out...

    Get started!!!! Good Luck!!!

    Steve K

  3. #3

    Join Date
    Apr 2011
    Location
    Hemel Hempstead, UK
    Posts
    462

    Re: Risk of fungus

    Yabbut - this is lens, not mould on the bellows or wooden parts (from the OP's description).

    In which case, it's fungus eating the balsam adhesive between the cells of the lens. Remove it replace, and the problem has gone away.

    Or live with it for a while; unless you can't see through it, the worst you'll get is usually only a little flare and/or reduced contrast.

    Neil

  4. #4

    Join Date
    Jan 2009
    Location
    Denmark
    Posts
    5,286

    Re: Risk of fungus

    I have a somewhat different opinion about fungus!

    Giving the camera a general clean-up is a good idea. But, to honest, the air is full of fungus spores which will inevitably reach most surfaces. The important thing is keep the stored camera and lens in a dry and cool atmosphere.

    Changes in air humidity and temperature means that water molecules will appear on metal and glass surfaces, whilst leather and materials do not get a wet surface. Old uncoated lenses usually get very whispy fungus which wipes off - leaving, at worst, some surface blooming. Modern (post- 1945) coated lenses get nasty fungus where there is transformation of the fluorides into fluoric acid which etches the glass well beyond the critical point.

    The "Air tight box" and "active silica" is, in my opinion overkill. The day you forget to dry out the camera before this sort of storage will be expensive!

  5. #5
    Foamer
    Join Date
    Oct 2010
    Location
    South Dakota
    Posts
    1,004

    Re: Risk of fungus

    I too would not store in an air tight container. If the camera/lens has any dampness, it won't be able to dry out until you use the camera again, whenever that may be.


    Kent in SD
    Die Gedanken sind Frei

  6. #6
    tgtaylor's Avatar
    Join Date
    May 2006
    Location
    San Francisco Bay Area
    Posts
    3,838

    Re: Risk of fungus

    I live near the coast where the RH generally runs 50 - 60%. Since August, 2000, when I bought the camera new, I've stored the Pentax67II wrapped in a Domke lens wrap along with 9 Pentax 67 lens in their soft storage sacks in an aluminum Hakuba case with a few packets of silica dispersed without a problem: The glass is as pristine as when they were new. If the camera/lens were exposed to rain or heavy fog during an outing, I'll dry and let them "air-out" before storing. Once the fog/RH was so high that the cloth focal plane was soaked but it dried out as new. My other cameras and lens are stored in Pelican waterproof cases.

    Thomas

  7. #7

    Join Date
    Dec 2001
    Location
    San Joaquin Valley, California
    Posts
    8,213

    Re: Risk of fungus

    I'd simply replace that fungal challenged lens and press on. Since I don't know what the practices are in the UK, speak with local LFer's and listen to what storage solutions works for them. As I recall there is quite a LF support group in the UK. There are certainly members from the UK on this forum who can fill you in on the skinny.
    I steal time at 1/125th of a second, so I don't consider my photography to be Fine Art as much as it is petty larceny.
    I'm not OCD. I'm CDO which is alphabetically correct.

  8. #8

    Join Date
    May 2010
    Location
    St. Louis, Mo.
    Posts
    2,677

    Re: Risk of fungus

    Quote Originally Posted by John Kasaian View Post
    I'd simply replace that fungal challenged lens and press on. Since I don't know what the practices are in the UK, speak with local LFer's and listen to what storage solutions works for them. As I recall there is quite a LF support group in the UK. There are certainly members from the UK on this forum who can fill you in on the skinny.
    Hey John, don't people out in California consider fungus health food?

  9. #9
    Jac@stafford.net's Avatar
    Join Date
    Dec 2012
    Location
    Winona, Minnesota
    Posts
    4,093

    Re: Risk of fungus

    I have found that fungus cannot grow if the temperature is less than 70F and relative humidity is less than 60.

  10. #10
    Foamer
    Join Date
    Oct 2010
    Location
    South Dakota
    Posts
    1,004

    Re: Risk of fungus

    Quote Originally Posted by Alan Gales View Post
    Hey John, don't people out in California consider fungus health food?

    Ah, no. I've heard they smoke it.


    Kent in SD
    Die Gedanken sind Frei

Similar Threads

  1. Replies: 72
    Last Post: 29-Oct-2016, 19:21
  2. Risk of fungus
    By michaelstubbs in forum Cameras & Camera Accessories
    Replies: 4
    Last Post: 23-Oct-2015, 13:22
  3. Risk Taking and LF Photography Experiences
    By Frank Petronio in forum On Photography
    Replies: 42
    Last Post: 31-Dec-2006, 16:55
  4. Making a recessed lensboard and figuring out angles,vignetting risk etc
    By Nick_3536 in forum Cameras & Camera Accessories
    Replies: 6
    Last Post: 24-Aug-2004, 11:08
  5. Health Risk of Pyro
    By steve simmons in forum Darkroom: Film, Processing & Printing
    Replies: 41
    Last Post: 17-Jun-2004, 15:49

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •