Results 1 to 7 of 7

Thread: Homemade lens for 8X10

  1. #1
    Randy's Avatar
    Join Date
    Dec 2010
    Location
    Virginia, USA
    Posts
    1,486

    Homemade lens for 8X10

    Back in August I had posted this image in the X-ray film shooting and developing thread:



    I noted that I used a 13" homemade lens. Some were curious about the lens so I described it. Another member asked for a more detailed description of the lens but I had not visited the thread again until today - so - apologies for the delay - for any interested in my amateur attempt at lens making...here it is. Please bare in mind that I barely graduated high school many years ago and have no higher education, other than life's failures over and over again.



    Materials

    1 - Tiffen Photar Plus 3 Series 7 close-up filter (like you would screw onto the end of your 35mm camera lens for shooting close-ups of flowers - only this one has no threads, so I had to use the adapter and retaining rings - this lens has a focal length of about 13" or 330mm)
    1 - Tiffen Series 7 Adapter Ring
    6 - Tiffen Series 7 Retaining Rings (I used 6 retaining rings simply because I had them - I figured they would make a decent lens tube)
    1 - 77mm-58mm Step-down ring (to make a mounting flange for mounting the lens to homemade lens-board)
    1 - Black construction paper for making an aperture (cut round to fit inside retaining ring)



    I tend to use what I have on hand, and my calculation method of determining what will work and what will not is to waste hours making it, and if it doesn't work, throw it in the scrap pile and go watch TV. If it does work, my calculations were correct.

    I made this lens after the fashion of a Walloston Landscape (Meniscus) lens - the lens is at the rear, concave side facing front-words, and the aperture is at the front of the lens, in my case, about 1" from the lens. I believe I tried it both ways, flipping the lens with the concave side facing the film, and I believe there was a difference, and I liked my current configuration better. For my configuration, the lens is about f/7 without the aperture installed, and f/16 with it - the aperture hole is 20mm in diameter - cut with razor knife.



    I taped the center retaining rings so that they wouldn't loosen - leaving the front end ring so I can remove the f/stop if I want, and the rear ring so I can remove the lens for cleaning.

    More photos momentarily...
    https://dl.dropboxusercontent.com/u/52893762/bigger4b.jpg

  2. #2
    Randy's Avatar
    Join Date
    Dec 2010
    Location
    Virginia, USA
    Posts
    1,486

    Re: Homemade lens for 8X10


    This shows the rear adapter unscrewed from the retaining ring.


    The Tiffen +3 close-up filter


    The 77mm-58mm step-down adapter - these things are great for making experimental lens flanges because they allow enough space for drilling holes for mounting to a lens-board.



    That's it in a nutshell. Hope this helps answer any questions.
    https://dl.dropboxusercontent.com/u/52893762/bigger4b.jpg

  3. #3
    Big Negs Rock!
    Join Date
    Mar 2000
    Location
    Pasadena
    Posts
    1,188

    Re: Homemade lens for 8X10

    Nice work. I made a lens with a magnifying glass. It's a swirly impressionistic lens. Fun stuff.
    Mark Woods

    Large Format B&W
    Cinematography Mentor at the American Film Institute
    Past President of the Pasadena Society of Artists
    Director of Photography
    Pasadena, CA
    www.markwoods.com

  4. #4

    Join Date
    Feb 2015
    Location
    Sheridan, Colorado
    Posts
    2,434

    Re: Homemade lens for 8X10

    Neat stuff. Many people spend a LOT of money buying soft-focus lenses, when they can do what you have done -- for basically nothing. There are a LOT of close-up lenses that can create all sorts of results:

    http://www.subclub.org/fujinon/close-up.htm

    I use close-up lenses an a Copal #1, but the shutter, as the lens, is completely variable. Good CU lenses can create results from very blurry to pretty sharp..

  5. #5
    William Whitaker's Avatar
    Join Date
    May 2002
    Location
    NE Tennessee
    Posts
    1,423

    Re: Homemade lens for 8X10

    I like the image a great deal. A little disturbing... It's working on me.
    Nice job!

  6. #6

    Join Date
    Aug 2013
    Location
    Chicago
    Posts
    1,856

    Re: Homemade lens for 8X10

    I have done something similar, mounting a 250mm FL achromatic close up lens behind a shutter, with empty filter rings for spacing from the diaphragm:
    https://www.flickr.com/photos/michae...in/dateposted/

    In point of fact, I gutted my Fuji 250SF for its shutter for this project because I found the SF aspect of the lens to be quite disappointing. :-)
    Thanks, but I'd rather just watch:
    Large format: http://flickr.com/michaeldarnton
    Mostly 35mm: http://flickr.com/mdarnton
    You want digital, color, etc?: http://www.flickr.com/photos/stradofear

  7. #7

    Join Date
    Mar 2004
    Location
    San Francisco Bay Area
    Posts
    508

    Re: Homemade lens for 8X10

    Stepping rings, especially if you can find one made of brass, do make good mounting flanges for odd jobs. I have my EL-Nikkor 240mm mounted on my Beseler using one.

    I have a +3 simple meniscus as a push-fit in an old Seikosha-S shutter. It is totally the 'wrong' way around - convex surface forward, lens in front of the shutter - but surprisingly good, if a bit specialized. And since it came from the parts box, I can't complain.

Similar Threads

  1. Homemade lens board ?
    By Gerry Harrison in forum Cameras & Camera Accessories
    Replies: 16
    Last Post: 16-Aug-2006, 02:43
  2. suggestion for homemade 8x10 polaroid
    By Jae in forum Cameras & Camera Accessories
    Replies: 8
    Last Post: 24-Feb-2006, 08:36
  3. Homemade lens boards?
    By Craig Allen in forum Cameras & Camera Accessories
    Replies: 15
    Last Post: 31-Mar-2001, 12:17

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •