Results 1 to 9 of 9

Thread: Using a modern power supply with an old enlarger (Durst 1200, DIY)

  1. #1

    Join Date
    Sep 2009
    Location
    Austin TX
    Posts
    25

    Using a modern power supply with an old enlarger (Durst 1200, DIY)

    Not sure if what I've done is interesting enough to show here, but someone may find it useful.

    I have a Durst AC1200 with a bum power supply, and even when it was working I spent more time troubleshooting 30 year old circuitboards than I did printing.

    I was able to find a good deal on a VLS501 head with no power supply, so I figured I could use a modern "Switching" power supply instead.



    The Durst EST500 outputs 23.5 VDC at 275 Volt-Amps (11.7A). I figured that any modern "Switching" power supply of similar capacity would work. A hopeful sales guy from work dropped off a 24 VDC 10A power supply as a "freebie", so I figured I'd give it a shot. Seen below is a PULS CP10.241-S1 Power Supply and my Open Source F-Stop Timer (link).



    Here is a diagram of how I connected the power supply to the enlarger:





    And so far, I'm getting very consistent bulb warm-up times, extremely consistent prints, and best of all, I'm not dependant on a 30 year old Italian power supply.

    Let me know if you have any questions.

    Note: This is a very expensive industrial power supply meant for high-reliability environments. Virtually any inexpensive DIN-rail mount power supply with sufficient specs from Mouser or Digikey would function equally as well. I've seen similar power supplies go for ~$25 on eBay.

    Disclaimer: Not an electrician, so mess with electricity at your own risk. There is enough power here to kill you, so be careful out there.

  2. #2
    Cor's Avatar
    Join Date
    Nov 2006
    Location
    Leiden, The Netherlands
    Posts
    635

    Re: Using a modern power supply with an old enlarger (Durst 1200, DIY)

    Thanks for posting, sure is very useful for future reference, there quite a few of these machines out there !

    Best,

    Cor

  3. #3
    Drew Wiley
    Join Date
    Sep 2008
    Location
    SF Bay area, CA
    Posts
    10,591

    Re: Using a modern power supply with an old enlarger (Durst 1200, DIY)

    My favorite trick is to install bulbs that run either straight 115v or straight 240v, then throw away the stupid power supply! Works every time if your in-house voltage reads consistent and you isolate any odd circuits, which are generally 115 anyway.

  4. #4

    Join Date
    Jul 2006
    Location
    Collinsville, CT USA
    Posts
    634

    Re: Using a modern power supply with an old enlarger (Durst 1200, DIY)

    Very simple and basic thing to check out on any "rewired" enlarger. The plug has 2 prongs. The wide one is the neutral and attached to the female screw part of the bulb's socket. The narrow one is hot and attached to the center piece of metal in the bottom/back of the bulb's socket. If the connections are reversed, the outside of your enlarger may be hot and in the environment of a darkroom a VERY, VERY dangerous thing.

  5. #5
    ic-racer's Avatar
    Join Date
    Feb 2007
    Posts
    4,753

    Re: Using a modern power supply with an old enlarger (Durst 1200, DIY)

    When eliminating the low voltage power supply recall some 120/115V MR 16 lamps fit a GY5.3 socket (flat pins). Whereas the common low-voltage MR 16 lamps can have the round pins with GU 5.3 base. New socket is a good idea for any enlarger refurbish project anyway.

  6. #6

    Join Date
    May 2015
    Location
    SooooCal/LA USA
    Posts
    1,001

    Re: Using a modern power supply with an old enlarger (Durst 1200, DIY)

    One concern is that many SMPS P/S's have a turn on delay, and sometimes a ramp up voltage, so for short exposure times with a timer, this might affect exposure...

    Steve K

  7. #7

    Join Date
    Feb 2013
    Posts
    175

    Re: Using a modern power supply with an old enlarger (Durst 1200, DIY)

    For anybody else with the same problem, All Electronics (www.allelectronics) has a similar power supply-24VDC-10 amp. Catalog # is PS-2401 and price is $37.50. Hope this helps!

  8. #8

    Join Date
    Sep 2009
    Location
    Austin TX
    Posts
    25

    Re: Using a modern power supply with an old enlarger (Durst 1200, DIY)

    Quote Originally Posted by LabRat View Post
    One concern is that many SMPS P/S's have a turn on delay, and sometimes a ramp up voltage, so for short exposure times with a timer, this might affect exposure...

    Steve K
    Steve, that was a problem when I was running my relay on the wall power side of the power supply. I had inconsistent ramp-up times, sometimes 1.5-2 seconds. By moving my relay to the 24V side, the power supply is "on" during the entire darkroom session, so it has a turn on delay in the milliseconds once the circuit is closed.

  9. #9

    Join Date
    Feb 2008
    Location
    The Highlands of Scotland
    Posts
    78

    Re: Using a modern power supply with an old enlarger (Durst 1200, DIY)

    I have an AC1200 with a failed controller. I sent it for repair but it came back as uneconomical to repair.

    fj55mike - If you need me to measure voltages etc, let me know and i'll dig out the PSU. Obviously i'm on 240vac in the UK and the readings would be unloaded.

    I ended up going for an MG500 head and controller instead.

Similar Threads

  1. Durst CLS450 Power supply
    By Crowbar56au in forum Darkroom: Equipment
    Replies: 8
    Last Post: 14-Feb-2016, 19:38
  2. Durst 450 Power Supply
    By don73 in forum Darkroom: Equipment
    Replies: 2
    Last Post: 30-Oct-2013, 14:31
  3. Durst Lab 1200, CLS450, TRA 450 power supply
    By ChrisN in forum Darkroom: Equipment
    Replies: 6
    Last Post: 20-Nov-2009, 05:02
  4. Durst 450 cls power supply
    By sangulon in forum Darkroom: Equipment
    Replies: 0
    Last Post: 21-Nov-2007, 16:29

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •