Results 1 to 6 of 6

Thread: Replacement of the Graflok Back

  1. #1

    Smile Replacement of the Graflok Back

    Hello everyone!

    I have got a Pacemaker Speed Graflex camera. But the Graflok back is too old to be used. The same type of the back (graflok back) is a little expensive and old in ebay. Is there anyone later and more reliable could replace the back? THX

    Bob

  2. #2

    Join Date
    Dec 2001
    Location
    NJ
    Posts
    8,470

    Re: Replacement of the Graflok Back

    Bob, there's just one Graflok back for Pacemaker Graphics. Old ones -- my oldest was made in 1949, the year the Graflok back was introduced -- still work very well. Tell us more about your problem and why you think age has anything to do with it.

  3. #3

    Join Date
    Jan 2011
    Location
    Montana
    Posts
    102

    Re: Replacement of the Graflok Back

    About the only thing that can go wrong with a Graflok is getting dirt and corrosion in the springs, which can happen if a camera is stored for a long period of time. The back castings are made from magnesium, which is kind of prone to surface corrosion in unpainted areas (or where the paint is worn/chipped). The only other problem I've seen is on cameras that were stored for long periods of time with a film holder stuck in them (or worse, a Grafmatic). You know, where Grandpa put it away in the attic that way and it sat for 20 years. The springs tend to get kind of floppy when left under tension for that long, but the back will still usually be functional.
    If it's a corrosion issue, the best way to clean it is to disassemble it and give it a bath in an ultrasonic machine...if you don't have access to that, hot soapy water and an old toothbrush will help a lot. Lube the pivot points a drop of light synthetic oil and work the pivots back and forth to work it in. I've worked on a lot of these, and have yet to see one that couldn't be saved.

  4. #4

    Re: Replacement of the Graflok Back

    Thanks for your help, Dan. The problem is that the spring of the back is no elastic and I can't insert the film holder. Furthermore, there is a lot of corrosion on the surface.

  5. #5

    Re: Replacement of the Graflok Back

    Thanks a lot. You are right. That's my problem. The spring is no elastic and I can't insert the film holder. There is also a lot of corrosion on the surface. I can only unscrew the screw to remove the ground glass. But I have no idea to disassemble it to replace the worn spring.

  6. #6

    Join Date
    Dec 2001
    Location
    NJ
    Posts
    8,470

    Re: Replacement of the Graflok Back

    I haven't looked at them for ages, but one of the manuals on www.southbristolviews.com might show how the focusing panel (that's where the springs are) comes apart. If it comes to that, you need a focusing panel, not a complete back assembly.

Similar Threads

  1. Original Graflok or Toyo Graflok back
    By rkamarowski in forum Cameras & Camera Accessories
    Replies: 2
    Last Post: 10-Feb-2014, 12:45
  2. Replies: 9
    Last Post: 23-Jan-2012, 21:32
  3. Will a Horseman 6x12 back fit on my Crown Graphic with Graflok back?
    By Joffre Swait in forum Darkroom: Film, Processing & Printing
    Replies: 4
    Last Post: 19-Nov-2003, 14:21

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •