Search:

Hello Alan,

I took the scanner to the local Epson agent, turned out that the issue was a miniscule piece of debris was stuck in the socket for the data cable. This appears to have been the cause...

Alan - thank you for your suggestion. I have removed all Apps, and reloaded Epson Scan and still no luck. The scanner its self does not seem to be going through its start up cycle correctly. ...

I have a Epson V850 Pro - and use both the Epson software and Silverfast software. I have tried to start up the scanner after several months of non use, all cables and plugs are in correctly,...

Thank you all again for your input and excuse my later response, for the past week I have been unable to access LF site due to some security setting in my computer.

Alan,

Thank you, I do not believe I clipped the highlights in the original scan , the problem I have is that I moved the right side maker on the histogram as far as it would go (to the right) ...

Thank you all for your input appreciated.

And Bruce your comments regarding the every high density neg and the opaque nature of silver make sense and helps me understand what is going on. With...

Hello all,

I am fairly new to scanning and encountering problems with high lights.

I am using a Epson V850 Pro scanner, Silverfast 8.8 software to scan 4x5 Tri X negatives in Grey scale 16...

Gentlemen - thank you all for your input, shared experience and suggestions, most appreciated. Ken Lee's site has much information, which will require some time to digest...

I do have a couple of...

Hello

I have recently purchased an Epson 850V and using the bundled scanning software Silverfast SE 8.8. I am new to this side of things, but progressing OK with scanning B&W negatives (35mm,...

Bernard - the batch number is 0232. FYI - The selenium toning made a noticeable difference to bring back the apparent gloss.

Hello All - to revert on my original post.

Firstly I followed the suggestion to develop the paper in a 2:1 dilution, same result. I checked the Box title and the delivery note - all correct. I...

Thanks for the comments. I will try a stronger Dektol mix, but on close inspection and compared with previous prints it sure looks like a different finish on the print. Different reflective level...

Hello
I have been using Fomabrom Variant 111 (fibrebased) for some time. Great results and I am happy with it. Dektol (5:1) for five minutes at approx. 20°c, Citric Acid for stop and either...

I am not sure hence my question, but will pick a rubbish negative and experiment

Thanks for the replies

Peter

I need some guidance please

I used chromium intensifier to increase contrast on a negative but went too far..... is there anyway to reduce the contrast?

Thank you

Peter

Excuse tardy reply, thanks for the info, happy to say that printed from the negs and much improved! Will sulfite the negs

Thank you
Peter

I have recently used Fotospeed Chromium Intensifier for some flat negatives. I mixed as per instructions, washed off the yellow residue and re-developed in print dev and washed. Good result, the...

I have just finished a printing session and the developer worked just fine, but became exhausted quicker than normal...

Thanks all, and HMG for the link to Kodak info site

Hello - I have just received several packages of Dektol powder from my supplier in the UK, brand new with expiry date Nov 2022. In the past the powder was white-ish, now it is a dirty brown...

Hi Doremus,

Just to revert I did the paper fog test you suggested and all good. New fixer stuck due to virus restrictions on shipping. So I reprinted the same neg and similar results.... at...

Doremus and Cor. Thank you for you suggestions.

I have checked the fixer for sediment etc and it’s fine no foreign substances, and it clears the film completely in the allotted time. I have...

Renato - I did not know that the type of stop bath can impact on fixing process - how so? I use citric acid (heaped teaspoon per litre of water) been using this for some years seems to work just...

Appreciate the comments - the mix ratio and the suggested time differs between the two products. Jerold I think you may be right !

Thank you
Peter

I have used Ifford Hypam fixer for some time - mixed as per manufacture recommended ratio. I have just changed to Fomafix (less costly) and mixed as per manufacture recommended ratio. I use Foma...

I also have the experience from time to time, totally random. I use deep tank, one shot dev, one shot citric acid stop and normal fixer but reuse several time. Water is house hold supply through a...

If anyone is familiar with the online magazine Lookinglass (which is excellent) do they know if it is still in existence. I have been trying to renew my subscription but I get no response to my...

I live in the South of France and we have tripod police too, they tend to be gate keepers on abbies, churchs and public buildings etc. After being told I was unable to use my tripod as it was...

I modified a hiking stick by drilling a hole down from the top and packing it with a bit of JB Weld, then shoving a piece of 3/8 - 16 threaded brass rod into the hole. Works about as well as any...

Thanks guys. The locator hole is a good idea. It's the first time I have ever seen these locator holes.

Peter

JoshuaT

I have the Schneider 150 APO lens and its excellent, in my experience produces very good results. It is small and light and readily available on ebay get one!

Peter

Suggestions please;

I have recently purchased a Fujinon W 120mm 5.6 lens (lens description is written on the outside rim of the front element) The shutter is a Copal N°0 but an older one, the...

Jon first time I have seen this vista in color , bravo it is surperb !

Alexmuir, no corresponding negative defects. The spots appear sometime after processing prints.
Peter

Koraks,

The papers are Ilford FB warmtone and Ilford Art FB , Dev is Tetnal Eukobrom no raw chemicals, this is only Dev I use. My darkroom is full light tight and safe lights tested and ok. So...

Dear All,

I have random black spots/ blotches appearing on some of my prints. Not very big approx 2mm in dia and looking like a small ink drop on blotting paper... No particular rhyme nor reason,...

Thanks again for the common sense Eric

Thanks for the suggestions, I have also found Bruce Barnbaum's w/s schedule too which I believe are excellent.
Cheers

Hello can anyone advise on worthwhile workshops in the Fall of this year where LF is used and there are darkroom facities available and naturally good instruction. I am not inexperienced but work in...

Thanks all and Doremus for your explanations. I have now read Thalmans link and the sub club link. Plenty to digest.
Thanks again to all who commented
Peter