large format parts? for use in a digital camera camera enclosure
i'm working on an enclosure for a time lapse project with a digital camera. i'm trying to figure out a controlled way to adjust the position of the camera within the enclosure. perhaps i could repurpose some large format camera parts to do the job.
any advice on relatively inexpensive parts? or even a kit? (is it possible?)
Re: large format parts? for use in a digital camera camera enclosure
Probably not enough info, but sounds like something for which you might use stepper motors and gears. McMaster-Carr might be a good source, or other sources used by those interested in robotics.
Re: large format parts? for use in a digital camera camera enclosure
McMAster-Carr looks interesting although i'm not sure how to find solutions to my problem.
I'm not looking for robotics. fingers can make the adjustments.
Re: large format parts? for use in a digital camera camera enclosure
Why don't you describe precisely what it it you're trying to do?
Re: large format parts? for use in a digital camera camera enclosure
You might search EBAY for Arca Swiss or Linhof parts. Many of those can be found as geared movements, which hopefully would provide accurate control.
Other than that, you could go for Edmund Scientific. They offer lots of staged movement pieces and mounting blocks that are geared. Prices are perhaps a bit higher than used large format.
Bogen/Manfrotto also offer some geared camera mounts and tripod head. Depending upon accuracy or markings, those might work quite well for you.
Re: large format parts? for use in a digital camera camera enclosure
How many axes do you need to move the camera in: X, Y, Z, rotate horizontally, rotate vertically, etc.? How far on each axis do you need to move the camera?
XY focus rails are readily available on ebay if you only need to move it a few inches. If you need rotation, take a look at spherical pano heads like Nodal Ninja.
I used aluminum extrusions from http://www.8020.net (they also have an ebay outlet) to build an XYZ stage for macro photography.
Re: large format parts? for use in a digital camera camera enclosure
My solution for this is simple if you have it around, otherwise it might be too expensive: Lego! It's easy to build a small platform that is being turned, just add some small gears that turn larger gears and it'll go extremely slow. Or add a radial drive to make it even slower.
Re: large format parts? for use in a digital camera camera enclosure
the 8020 stuff looks great although i'd like to find something smaller.
i'll try to describe it in better detail -
inside the enclosure, i'd like to be able to move the camera in the following directions
- closer or further away from the window on the enclosure
- vertically, an inch or two
- tilting the camera up or down (not sure thats a good description) but this looks like it might take care of it -
http://www.bhphotovideo.com/c/produc...ling_Base.html
I should also add that precision isn't necessarily as important as the ability to lock things down. The camera is likely to be positioned once. it may need to be serviced after that but hopefully a quick release plate will allow for easy removal and replacement with little camera movement.
Re: large format parts? for use in a digital camera camera enclosure
It's possible, it depends on how much time, labor and money you want to invest in that rig.
For time lapse you want a solid rig, unless the jittery look is what you're after.
Sounds like you're looking for a positioning stage, mucho bucks.
http://www.edmundoptics.com/onlineca...productid=1581
If precise positioning isn't paramount, and you're handy with tools
get a lab jack from eBay, which will give you the Y movement ( up /down )
XZ movements you would use a lead screw mounted to the lab jack at right angles,
one for your Z movement ( front / back ) and one for your X movement ( left / right)
with the lead screw you would have to make a frame to support the lead screw and the rods
that would be guide rails, and build a stage to support the lead screws and camera stage.
Or
in place of building the XZ movement mech, get two macro bellows units from the 'Bay
the rack and pinion movement is all there, just ditch the bellows and mount them to the lab jack.
Re: large format parts? for use in a digital camera camera enclosure
Quote:
Originally Posted by
mattkime
the 8020 stuff looks great although i'd like to find something smaller.
i'll try to describe it in better detail -
inside the enclosure, i'd like to be able to move the camera in the following directions
- closer or further away from the window on the enclosure
- vertically, an inch or two
- tilting the camera up or down (not sure thats a good description) but this looks like it might take care of it -
http://www.bhphotovideo.com/c/produc...ling_Base.html
I should also add that precision isn't necessarily as important as the ability to lock things down. The camera is likely to be positioned once. it may need to be serviced after that but hopefully a quick release plate will allow for easy removal and replacement with little camera movement.
A pan and tilt head mounted on a 4 way focus rail like this, http://cgi.ebay.com/4way-Macro-focus...item414badb31a, will give you all the movements except vertical. Since you're only positioning it once, the vertical could be done with shims or blocks.
I'd probably just mount the pan and tilt head on a piece of exterior grade plywood, position the camera, and screw it all down to the floor of the enclosure.