Film exposed through the base
Based on reading another thread I realize I have shot several 4x5 sheets with the emulsion side facing away from the lens instead of toward it. I thought I was loading correctly but I had the holders oriented landscape, side I was loading facing me, slid the film in with the notch on the upper right corner, dark slide to the left. At any rate, I have several sheets of TMax 100 that I guess are going to be severely underexposed? Is there any point in adjusting development time to compensate or should I just see what happens? I was planning on developing tonight, have a batch of D76 ready to go... Oddly enough I have a test negative I shot that looks printable to me and I'm sure I loaded it the same way, I suppose you could say the negative looks a very little light, therefore possibly underexposed?, but has good detail all the way through, although I haven't printed it
Film exposed through the base
I think that's a tough call, Bob. While increasing development might bring density and contrast back up to compensate for the reduced exposure caused by shooting through the base and anti-halation coating, it's not likely that you'd end up with negatives that are actually "normal". I think I'd be tempted to develop normally, and see what happens, expecting that I'd end up with "artsy" negatives that would require other-than-normal printing. By that, I mean images that would be akin to applying a series of Photoshop "filters" for artistic effect.
Film exposed through the base
Hi Bob,
Chalk it up to experience. I'm sure you realize by now, that the next time you load film into holders, orient the holder portrait, darkslide at the bottom. Hold the film by the notch, in your right hand, and load it into the holder with the notch in the upper right corner. If you orient the holder landscape, darkslide to the left, the notch should be in the lower right corner.
Negatives loaded with the base side facing the lens will not only be underexposed, but the shades of grey will also be messed up (that is not technical terminology). The light passed through the anti-halation layer, as well as the film base, in order to reach the emulsion layer. Compensating the development time won't save those negatives. Of course you'll get an image on the film. Try printing the negatives, it's the only way to prove it to yourself.
Film exposed through the base
Several years ago while working just north of Nome, Alaska, I knew a photographer who was using a lovely new Technika outfit complete with case, lenses and all the accessories.
He said he had taken a chance and purchased it from another photographer for only one hundred dollars. The previous owner said the camera had some sort of defect which even the factory repair facility couldn't fix. Not one picture ever came out. The camera was worthless and he was fed up with it.
When my friend got the outfit home and took everything apart, he noticed that all the holders were loaded with the film face down.
Sometimes it pays to gamble...
Film exposed through the base
I would suspect that focus would be off as well, maybe not critically, but at least by as much as the thickness of the film, much like unsharp masking.
Film exposed through the base
We have all made mistakes. That's one of the many ways we learn! I doubt that you will do it again. Just go shoot some more film, and enjoy life.
Film exposed through the base
"Do you mean vertically? Almost every nature magazine is set up for vertical landscape photos. I can think of none that are set up for horizontal formats at all."
Huh..?
Film exposed through the base
I assume landscape means the long dimension (5") is horizontal and portrait means the long dimension is vertical. When you read instructions regarding loading that say "the notch goes in the upper right corner" it makes a big difference whether the upper right corner is the right end of the 5" dimension or the right end of the 4" dimension
Film exposed through the base
See this thread: http://www.photo.net/bboard/q-and-a-fetch-msg?msg_id=0098zX
Film exposed through the base
When loading sheet film into a holder, if you grasp the film by the notched corner between the index finger and the thumb of your right hand, and hold it up in front of your face, you are looking at the emulsion side of the film (even in complete darkness).
The film only loads into the holder at one end and one direction. The thing to remember is to hang onto the film and don't change hands. It doesn't matter if the holder is oriented vertically (portrait) or horizontally (landscape) during the loading procedure.