View Full Version : SilverFast Ai 6.5 cropping tool sluggish?
I just upgraded from SilverFast Ai 6.0 to 6.5. What I have found is that the cropping tool is sluggish and slow to react. For example, whenever I attempt to adjust one of the sides or top or bottom there is a delay and then the dreaded OSX circle of death starts to spin, and then stops after a couple of seconds. Is there some fix for this? The cropping took in 6.0 was very responsive.
Sandy King
Kirk Gittings
3-Jul-2007, 12:03
Sorry, I haven't seen this in PC's.
nils_heidorn
12-Jul-2007, 07:32
Dear Sandy,
could you give the latest Web download 650r8a a try, as we optimized the crop frame drawing after some changes to enable free rotation.
Please give it a try and let me know.
BTW: wich machine are you using ?
Greetings,
Nils
sanking
12-Jul-2007, 07:43
Dear Sandy,
could you give the latest Web download 650r8a a try, as we optimized the crop frame drawing after some changes to enable free rotation.
Please give it a try and let me know.
BTW: wich machine are you using ?
Greetings,
Nils
Nils,
Thanks for the reply. I am using SilverFast 6.5 and the Epson 4990 with a 24" Intel iMac.
Sandy
nils_heidorn
12-Jul-2007, 07:51
Dear Sandy,
your machine seems fine to me :-)
Well, please give the 650r8a Version a try ( i assume from the first date of your postings that you are using a 650r6 or earlier ).
Greetings,
Nils
sanking
14-Jul-2007, 17:09
Dear Sandy,
could you give the latest Web download 650r8a a try, as we optimized the crop frame drawing after some changes to enable free rotation.
Please give it a try and let me know.
BTW: wich machine are you using ?
Greetings,
Nils
Nils,
I have tried to download the revision several times but each time I am asked to register the product, even though I purchased it directly from SilverFast. Then when I try to go to the site it will not open. I just tried this evening for the fourth time and same result. I will send you the serial number if you can help.
Sandy.
nils_heidorn
16-Jul-2007, 00:43
Dear Sandy,
you can just use the "downloads" section of www.silverfast.com, select your scanner platform etc.
http://www.silverfast.com/get_demo/en.html
Greetings,
Nils
sandy - did you get 6.5 to work with your 4990 on mac? i didn't ...
sanking
31-Jul-2007, 15:01
sandy - did you get 6.5 to work with your 4990 on mac? i didn't ...
Yes, it works fine for me on the iMac with System OS 10.4.x and Photoshop CS.
I just obtained CS3 but have not yet had the time to try it out with SilverFast and the 4990.
Sandy
sandy - did you get 6.5 to work with your 4990 on mac? i didn't ...
OK, an update.
I installed Photoshop CS3 on my Intel iMac and SilverFast 6.5 with the Epson 4990 works fine.
However, to install Photoshop I had to update the System to OS 10.4.10 from some other 10.4.x system I had installed.
After that, just make sure that the Photoshop Plugin for SilverFast is installed in the same folder as Photoshop CS3.
Sandy King
hmm, and does the multi-exposure work?
i could only get 6.5 to work at smaller scan sizes (<100mB) and not at all with m-e turned on
hmm, and does the multi-exposure work?
i could only get 6.5 to work at smaller scan sizes (<100mB) and not at all with m-e turned on
Will be on the look for these problems. So far I have not tried multi-exposures or scans larger than 100mb.
Sandy
OK, I just made a few scans of over 500mb and had no problem at all with the combination of SilverFast/CS3/4990 on an Intel iMac running OS 10.4.10.
Sandy
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.